Do you have a question about the Digital and is the answer not in the manual?
Questions and answers
Tatyasaheb Nawale
January 30, 2025
How to set normal washing clothes
1 comments:
Mr. Anderson
February 10, 2025
To set a normal wash cycle on the IFB Digital washing machine:
1. Sort and Load Clothes – Separate garments based on fabric type and load them into the drum. 2. Add Detergent – Pull out the detergent tray and fill: - Pre-wash chamber (Marked I) if a pre-wash cycle is needed. - Main wash chamber (Marked II) with detergent for every wash. - Fabric conditioner chamber (Marked “ ”) if using additives. 3. Select Wash Program – Choose the appropriate wash program based on fabric type. For normal washing, select the Cottons program (Cold, Mild 45°C, Warm 60°C, or Hot 95°C). 4. Set Additional Options – Adjust settings like water temperature or spin speed if needed. 5. Start the Machine – Close the detergent tray and press the start button to begin the cycle.
Ensure the machine is connected to power and water before starting.
Page 1
Advancing the science of washing OPERATING MANUAL...
Page 3
Environmental protection / conservation issues Before using your machine for the first time...
Page 6
Environmental Protection/ Conservation Issues Before Using Your Washing Machine For The First Time Environmental Protection/ Conservation Issues Your washing machine uses water, energy and detergent efficiently, thereby protecting the environment and reducing your household costs. Using your washing machine in an efficient and environmentally friendly manner: Do not exceed recommended load.
Part 4: Program Selection and Washing Machine Operation Insert the plug. Press the On/Off button and then the Door open button. Open the door. Place your laundry into the machine according to the recommended load capacity and close the front door. Select the program according to the dirt strength and the thermostat value by means of Program Selection Table given on the following Pages.
Part 5: Care and maintenance Water intake filter Detergent dispenser At the end of the water intake connection module and water inlet To clean the detergent residues, remove the detergent dispenser hose-tap side, there exists filters. These filters prevent any dirt from its place by pressing on the area marked on siphon.
Safety Precautions Ensure that the machine is properly balanced on four adjustable feet. Ensure that the machine is connected to 3 pin socket with good earth and 16 Amp MCB or other automatic short circuit protection devices. The machine is tested with water during assembly for performance checking.
Page 26
Avoid the machine coming in contact with floor cleaning chemicals.* Do not wash or spray water over the switch or control panel. Do not allow children/pets to play with the machine. Do not wash shoes or utensils in the machine. Keep machine away from fire or heat.
INSTALLATION REPORT IFB WASHING MACHINE Model : __________________ Serial No. : ______________Customer’s Name : __________________ _________________________________________________Tel. No. ___________________________ Address :___________________________________________________________________________ __________________________________________________________________________________ Installation Check Points Machine Delivered on : __________________ Machine Installed on :_______________ 1. Any Major transit damage to the machine observed 2.
Need help?
Do you have a question about the Digital and is the answer not in the manual?
Questions and answers
How to set normal washing clothes
To set a normal wash cycle on the IFB Digital washing machine:
1. Sort and Load Clothes – Separate garments based on fabric type and load them into the drum.
2. Add Detergent – Pull out the detergent tray and fill:
- Pre-wash chamber (Marked I) if a pre-wash cycle is needed.
- Main wash chamber (Marked II) with detergent for every wash.
- Fabric conditioner chamber (Marked “ ”) if using additives.
3. Select Wash Program – Choose the appropriate wash program based on fabric type. For normal washing, select the Cottons program (Cold, Mild 45°C, Warm 60°C, or Hot 95°C).
4. Set Additional Options – Adjust settings like water temperature or spin speed if needed.
5. Start the Machine – Close the detergent tray and press the start button to begin the cycle.
Ensure the machine is connected to power and water before starting.
This answer is automatically generated