1. Manuals
  2. Brands
  3. Maxim Manuals
  4. Tiller
  5. RMT55H
  6. Operator's manual

Maxim TP50B Operator's Manual

Chain drive tillers
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Operator's Manual
Maxim Chain Drive Tillers
TP50B • MT50B • RMT50B • RMT55H • RMT50IC • RMT60R
WARNING
If incorrectly used this machine can cause severe injury. Those who use and
maintain the machine should be trained in its proper use, warned of its dangers,
and should read the entire manual before attempting to set up, operate, adjust,
or service the machine.
MAXIM MANUFACTURING CORPORATION
PO BOX 110 • Sebastopol, MS 39359 • www.maximmfg.com

Advertisement

Table of Contents
loading

Related Manuals for Maxim TP50B

Summary of Contents for Maxim TP50B

  • Page 1 Operator’s Manual Maxim Chain Drive Tillers TP50B • MT50B • RMT50B • RMT55H • RMT50IC • RMT60R WARNING If incorrectly used this machine can cause severe injury. Those who use and maintain the machine should be trained in its proper use, warned of its dangers, and should read the entire manual before attempting to set up, operate, adjust, or service the machine.
  • Page 2 Allow the engine to TINE ENGAGE LEVER 336777 3. After striking a foreign object, stop the engine, cool before storing in any enclosure. HANDLE CROSS BRACE (TP50B) 336768-A remove the wire from the spark plug, thoroughly HANDLE CROSS BRACE (MT50B) 336913...

  • Page 3: Setup Instructions

    Be careful not to kink the control cables. 2. Tiller model TP50B comes in two cartons. All other models are delivered in one carton. Carton #1 will have the complete tiller unit and the cultivator mounting bar. Carton #2 will have all the plow attach- ments and tractor tires.
  • Page 4 SET UP INSTRUCTIONS CONTINUED MT and TP Models right as you stand in an operating position. See Figure 1 and 2. Ref# Part # Quan. Description Part # Quan Description 5. Install the two handle bar tie braces between the holes in the transmission and the lower holes in the 336682 Main Frame Rail LH handle bars.

  • Page 5: Frame Assembly

    OPERATION FRAME ASSEMBLY BEFORE USING THIS MACHINE CHECK THE ASSEMBLY INCLUDING THE HANDLE AND CONTROLS. MAKE SURE ALL FASTENERS ARE TIGHT. MAKE SURE THE THROTTLE AND OTHER CONTROLS WORK CORRECTLY. BEFORE STARTING THIS TILLER, BE FAMILIAR WITH ALL OPERAT- ING CONTROLS. KNOW HOW TO DISENGAGE TINES, STOP FORWARD MOVEMENT AND SHUT OFF ENGINE.
  • Page 6 4. Repeat steps Number 2 and 3 above until the engine starts. If the engine fails to start after 3 pulls on the rope, repeat Step 1 above as necessary. Close choke after engine has responded. PART # DESCRIPTION 5. As the engine warms up, move the throttle lever to desired position. Alllow engine warm-up period be- fore operating tiller.

  • Page 7: Tine Adjustment

    OPERATING TIPS TRANSMISSION To acquire the knack of letting the tiller do the work without effort on the part of the operator, we offer the following suggestions: 1. Adjust drag stake so the handles are at such a height that your arms hang straight down to contact them.

  • Page 8: Parts Breakdowns

    Adjustments continued PARTS BREAKDOWNS 5. Re-tighten engine mounting bolts. TINES 6. Remove all the slack from clutch cable and hook spring in proper chain link. 7. Check your adjustment by starting the tiller and holding the tines off the ground. If the tines turn without any hand pressure on the clutch lever, the adjustment is too tight.

This manual is also suitable for:

Mt50bRmt50bRmt55hRmt50icRmt60r

Table of Contents