Page 1
Hoshizaki Hoshizaki America, Inc. Cubelet Icemaker / Dispenser Models DB-200H INSTRUCTION MANUAL “A Superior Degree of Reliability” www.hoshizaki.com Issued: 6-5-2001...
Page 2
HOSHIZAKI provides this manual primarily to assist qualified service technicians in the installation, maintenance and service of the ice dispenser. Should the reader have any questions or concerns which have not been satisfactorily addressed, please call or write to the HOSHIZAKI Technical Support Department for assistance.
• Please review this manual. It should be read carefully before the ice dispenser is installed and operated. Only qualified service technicians should install, service and maintain the ice dispenser. This manual should be made available to the technician prior to installation, maintenance or service. •...
I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING See NAMEPLATE for electrical specifications. The nameplate is located on the upper part of the Right Side Panel. We reserve the right to make changes in specifications and design without prior notice.
2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_...
Page 6
[b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M...
Page 7
[c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H...
KM-500M, KM-630M, KML-250M, KML-350M, KML-450M, or KML-600M. The use of this ice dispensing bin in combination with any cuber or flaker, other than a HOSHIZAKI Crescent Ice Cuber cannot be recommended. 2. Remove shipping carton, tape(s) and packing to prevent damage to the ice dispensing bin.
2. LOCATION 2. LOCATION 2. LOCATION 2. LOCATION 2. LOCATION This ice dispensing bin is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F. To the icemaker, water temperature should be within +45°F to +90°F. Extended periods of operation at temperatures outside of these limitations may cause unsatisfactory results.
3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. It is especially important that the icemaker/ice dispensing bin is leveled in both left-to-right and front-to-rear directions.
Page 11
*Note: With KML models, Top Panels are not necessary. Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1...
4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 1. Electrical connection must be made in accordance with the instructions on a “WARNING” tag, provided with the pig tail leads in the Junction Box. 2.
5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 1. A drain outlet, 3/4" FPT, is located at the rear of the ice dispensing bin. 2.
7. START UP 7. START UP 7. START UP 7. START UP 7. START UP 1) Start up the icemaker. See the “START UP” instructions on the icemaker. 2) Allow at least three (3) cycles of ice production, and then place a proper container in the ice station.
1. CLEANING INSTRUCTIONS 1. CLEANING INSTRUCTIONS 1. CLEANING INSTRUCTIONS 1. HOSHIZAKI recommends cleaning this unit at least once a year. (See the “CLEANING INSTRUCTIONS” on the icemaker.) More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker/ice dispensing bin, do not use ammonia type cleaners.
Page 17
Spout of the Spout of the Spout of the Spout of the Spout of the Front Panel Front Panel Front Panel Front Panel Front Panel Chute Chute Chute Chute Chute Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Agitator...
7) Scrub the Shutter Assembly and Spout—after removing them—using the cleaning solution of item 6. See Fig. 5. a) Remove the Snap Pin fitted to the Shutter Shaft and shift the Shaft to the left. Then the Shutter Assembly can be removed from the bin. b) Pull out on the sides of the Hook to release the Spout.
Page 19
HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A4JB10C...
Need help?
Do you have a question about the DB-200H and is the answer not in the manual?
Questions and answers