Hoshizaki DB-130H Instruction Manual
  1. Manuals
  2. Brands
  3. Hoshizaki Manuals
  4. Ice Maker
  5. DB-130H
  6. Instruction manual
Hoshizaki DB-130H Instruction Manual

Hoshizaki DB-130H Instruction Manual

Ice dispensing bin
Hide thumbs Also See for DB-130H:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Instruction Manual
Reliability is a
beautiful thing
TM
ICE DISPENSING BIN
DB-130H
INSTRUCTION MANUAL
ISSUED:
JUNE 5, 2001
™
REVISED: DEC. 10, 2003

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DB-130H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hoshizaki DB-130H

Summary of Contents for Hoshizaki DB-130H

  • Page 1 Reliability is a beautiful thing ICE DISPENSING BIN DB-130H INSTRUCTION MANUAL ISSUED: JUNE 5, 2001 ™ REVISED: DEC. 10, 2003...
  • Page 2 HOSHIZAKI provides this manual primarily to assist qualified service technicians in the installation, maintenance and service of the ice dispenser. Should the reader have any questions or concerns which have not been satisfactorily addressed, please call or write to the HOSHIZAKI Technical Support Department for assistance.

  • Page 3: Table Of Contents

    • Please review this manual. It should be read carefully before the ice dispenser is installed and operated. Only qualified service technicians should install, service and maintain the ice dispenser. This manual should be made available to the technician prior to installation, maintenance or service. •...

  • Page 4: Specifications

    I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING 1. NAMEPLATE RATING See NAMEPLATE for electrical specifications. The nameplate is located on the upper part of the right side panel. We reserve the right to make changes in specifications and design without prior notice.

  • Page 5: Dimensions/Connections

    2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS...

  • Page 6: Installation And Operating Instructions

    KM-500M, or KM-630M. It cannot be recommended to use this ice dispensing bin in combination with any cuber or flaker other than a Hoshizaki Modular Crescent Ice Cuber. 2. Remove shipping carton, tape(s) and packing to prevent damage to the ice dispensing bin.

  • Page 7: Location

    2. LOCATION 2. LOCATION 2. LOCATION 2. LOCATION 2. LOCATION This ice dispensing bin is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F. To the icemaker, water temperature should be within +45°F to +90°F. Extended periods of operation at temperatures outside of these limitations may cause unsatisfactory results.

  • Page 8: Set Up

    3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. It is especially important that the icemaker/ice dispensing bin is leveled in both left-to-right and front-to-rear directions.
  • Page 9 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1...

  • Page 10: Electrical Connection

    4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 1. Electrical connection must be made in accordance with the instructions on a “WARNING” tag, provided with the pigtail leads in the Junction Box. 2. To prevent possible electrical shock to individuals or extensive damage to the equipment, install a proper ground wire to the ice dispensing bin that meets local code requirements.

  • Page 11: Drain Connections

    5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 • A drain outlet, 3/4” female thread, is located at the rear of the ice dispensing bin. •...
  • Page 12 Fig. 4 Fig. 4 Fig. 4 Fig. 4 Fig. 4...

  • Page 13: Start Up

    7. START UP 7. START UP 7. START UP 7. START UP 7. START UP 1) Start up the icemaker. See the “START UP” instructions on the icemaker. 2) Allow at least three cycles of ice production, and then place a proper container in the ice station.

  • Page 14: Cleaning And Maintenance Instructions

    1. CLEANING INSTRUCTIONS 1. CLEANING INSTRUCTIONS 1. CLEANING INSTRUCTIONS 1. HOSHIZAKI recommends cleaning this unit at least once a year. (See the “CLEANING INSTRUCTIONS” on the icemaker.) More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker/ice dispensing bin, do not use ammonia type cleaners.
  • Page 15 Spout of the Spout of the Spout of the Spout of the Spout of the Front Panel Front Panel Front Panel Front Panel Front Panel Chute Chute Chute Chute Chute Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Agitator...

  • Page 16: [B] Sanitizing Procedure

    7) Remove the Shutter Assembly and Spout and scrub them using the cleaning solution made in step 6. See Fig. 5. a) Remove the Snap Pin fitted to the Shutter Shaft and shift the Shaft to the right. Then the Shutter Assembly can be removed from the bin. b) Pull out on the sides of the Hook to release the Spout.
  • Page 17 HOSHIZAKI HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH PEACHTREE CITY, GA 30269...

Table of Contents