Advertisement
1
2
3
4
5
6
3
INSTRUMENT PANEL
4
7
8
9
•
To return to a previously set speed, press RSM.
1
WINDSHIELD WIPER FUNCTION
To cancel a set speed, press CNCL or tap the
•
Rotate the end of the control stalk away/toward
brake pedal. You will not erase the set speed.
you to increase/decrease the speed of the wipers.
•
To turn off cruise control, press and release the
OFF button or switch off the ignition.
Push the end of the stalk:
•
Quickly for a single swipe without fluid.
To control the audio system:
•
Hold briefly for three swipes with washer fluid.
•
Press VOL+/VOL– to increase or decrease
•
Hold for a longer wash cycle.
your volume level.
Autowipers*
•
Press
radio station, CD track or preset satellite
The wipers will function when the sensor detects
moisture on the windshield. The rain sensor will
radio channel.
continue to monitor the amount of moisture on
•
Press MEDIA repeatedly to access all possible
media sources.
the windshield and adjust the speed of the wipers
automatically. You can switch this feature on or off
•
Press
in the information display. Be sure you turn off the
•
Press
control prior to entering a car wash.
4
SERVICE ENGINE SOON LIGHT
2
LIGHTING CONTROL
Lights briefly when the ignition is turned on.
Headlamps off.
If it remains on or is blinking after you start the
Parking lamps on.
engine, the On-Board Diagnostics (OBD-II) system
detects a malfunction. Drive in a moderate fashion
Headlamps on.
and contact your authorized dealer as soon
Autolamps on. Automatically switches
as possible.
the exterior lamps on/off based on
available daylight.
5
ANTI-LOCK BRAKE SYSTEM
(ABS WARNING LIGHT)
Fog lamps on. To use, pull the lighting
control toward you.
Lights briefly when you switch on the ignition.
If the ABS light remains on or continues to flash,
3
STEERING WHEEL CONTROLS*
the system detects a malfunction. Contact your
To set your cruise control speed:
authorized dealer as soon as possible. Normal
a.
Press ON.
braking (less ABS) is still functional unless the
brake warning light
b.
Accelerate to the desired speed.
c.
Press and release SET+ and take your foot
6
INFORMATION DISPLAY*
off the accelerator.
The information display shows important vehicle
To change your set speed:
information through a constant monitoring of
vehicle systems. The system will notify you of
•
Press and hold SET+ or SET–. Release the
potential vehicle problems by displaying system
control when you reach the desired speed.
warnings followed by a long indicator tone.
•
Press and release SET+ or SET–. The set
For more information about your information
speed will change in approximately 1 mph
display functions, please see your Owner's Manual.
(2 km/h) increments.
7
ELECTRONIC SHIFT 4WD SYSTEM*
The electronic shift 4WD system allows you to
choose between 2WD, 4x4 AUTO*, 4x4 HIGH
or 4x4 LOW.
2H (2WD) sends power to the rear wheels only
and should be used for street and highway driving.
Provides optimal smoothness and fuel economy
at high speeds.
to access the previous/next
4A (4X4 AUTO)* provides electronic control
four-wheel drive with power delivered to the
front and rear wheels, as required, for increased
traction. This is appropriate for all on-road driving
conditions, including dry road surfaces, but is
to access voice recognition*.
especially useful on wet pavement, snow, dirt
to access SYNC
phone features*.
®
or gravel.
4H (4X4 HIGH) helps provide extra traction
while driving in snow or on icy roads or off road
situations. This mode is not intended for use on
dry pavement.
4L (4X4 LOW) uses extra gearing to provide
maximum power to all four wheels at reduced
speeds. Intended only for off-road applications
such as deep sand, steep grades or pulling heavy
objects. 4L (4x4 LOW) will not engage while the
vehicle is moving above 3 mph (5 km/h); this is
normal and should be no reason for concern.
Refer to Shifting to or from 4L (4x4 LOW) in the
Four-Wheel Drive chapter of your Owner's Manual
for proper operation.
also lights.
8
TRAILER BRAKE CONTROLLER*
9
HAZARD WARNING
FLASHER CONTROL
*if equipped
5
Advertisement
