Sony HCD-XB66 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Stereo System
  5. HCD-XB66
  6. Service manual

Sony HCD-XB66 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
HCD-XB66, HCD-XB660 are the tuner,
deck, CD and amplifier section in LBT-
XB66, LBT-XB660.
Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol a are trade-
marks of Dolby Laboratories Licensing Corporation.
Amplifier section
The following measured at AC 120/240 V, 50 Hz
DIN power output (Rated)
Continuous RMS power output (Reference)
Peak music power output (Reference)
Inputs
PHONO IN (phono jacks):
MIX MIC (phone jack):
VIDEO/MD (AUDIO) IN (phono jacks):
Outputs
PHONES (stereo phone jack):
VIDEO/MD (AUDIO) OUT (phono jacks):
SPEAKER:
MICROFILM
HCD-XB66/XB660
SPECIFICATIONS
140 + 140 watts
(8 ohms at 1 kHz, DIN)
170 + 170 watts
(8 ohms at 1 kHz, 10% THD)
3,000 watts
sensitivity 3 mV, impedance
47 kilohms
sensitivity 1 mV, impedance
10 kilohms
sensitivity 250 mV, impedance
47 kilohms
accepts headphones of 8 ohms or more
voltage 250 mV, impedance 1 kilohms
accepts impedance of 8 to 16 ohms.
Photo: XB66
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Base Unit Name
Optical Pick-up Name
Tape deck
Model Name Using Similar Mechanism
Section
Tape Transport Mechanism Type
CD player section
System
Laser
Laser output
Wavelength
Frequency response
Signal-to-noise ratio
Dynamic range
CD DIGITAL OUT
(square optical connector jack, rear panel)
Wave length:
Output level:
COMPACT DISC DECK RECEIVER
E Model
Australian Model
HCD-XB66
Mexican Model
HCD-XB660
HCD290/G330/XB3
CDM37LH-5BD29AL
BU-5BD29AL
KSS-213D/Q-NP
HCD-H881
TCM-220WR2
Compact disc and digital audio system
Semiconductor laser (λ = 780 nm)
Emission
duration: continuous
Max. 44.6 µW*
*This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
780 - 790 nm
2 Hz - 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB
600 nm
–18 dBm
– Continued on next page –

Advertisement

Table of Contents
loading

Related Manuals for Sony HCD-XB66

Summary of Contents for Sony HCD-XB66

  • Page 1 HCD-XB66/XB660 SERVICE MANUAL E Model Australian Model HCD-XB66 Mexican Model HCD-XB660 HCD-XB66, HCD-XB660 are the tuner, deck, CD and amplifier section in LBT- Photo: XB66 XB66, LBT-XB660. Dolby noise reduction manufactured under license Model Name Using Similar Mechanism HCD290/G330/XB3 from Dolby Laboratories Licensing Corporation.

  • Page 2: Table Of Contents

    4-track 2-channel stereo Frequency response (DOLBY NR OFF) SERVICING NOTES ..........3 60 - 13,000 Hz (±3 dB), using a Sony TYPE I cassette GENERAL 60 - 14,000 Hz (±3 dB), using a Sony TYPE II cassette Location of Controls ............4 Setting the Time ..............

  • Page 3: Servicing Notes

    AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH XB66 : Australian model 4-996-413-3π SONY PARTS WHOSE PART NUMBERS APPEAR AS XB66 : South African model 4-996-413-4π SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- XB660: Mexican model 4-996-413-8π...

  • Page 4: Location Of Controls

    SECTION 2 GENERAL LOCATION OF CONTROLS – Front Panel – 1 I /u (Power) button 2 DISPLAY/DEMO button 3 FILE (1-5) indicator 4 Fluorescent indicator tube 5 TUNER MEMORY button !§ 6 TUNING MODE button 7 TUNER/BAND button and indicator !¶...
  • Page 5 %º WAVE button %º %¡ %™ %£ %¢ %∞ %¡ SURROUND button %™ P FILE MEMORY button %£ GEQ CONTROL button %¢ P button and indicator (DECK B) %∞ p button (DECK B) %§ %§ ª button and indicator (DECK B) ^™...
  • Page 6 – 6 –...

  • Page 7: Disassembly

    SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. OPTICAL FRONT PANEL MAIN CD MECHANISM CASE BASE UNIT BD BOARD SECTION PICK-UP SECTION DECK SECTION (Page 12) (Page 13) (Page 7) (Page 8) (Page 9) (Page 9) (Page 13) SLED...
  • Page 8 FRONT PANEL SECTION 1 wire (flat type) (21 core) (CN205) 1 wire (flat type) (11 core) (CN206) 1 wire (flat type) (17 core) (CN102) 3 front panel section 2 four screws (BVTP3 × 8) 6 back panel MAIN BOARD 4 eleven screws (BVTP3 ×...
  • Page 9 1 flat wire (CN202) MAIN SECTION 2 connector (CN203) 4 main section 3 two screws (BVTP3 × 8) 3 screw (BVTP3 × 8) 3 two screws (BVTP3 × 8) CD MECHANISM DECK SECTION (CDM37LH-5BD29AL) 3 five screws (BVTP3 × 8) 4 CD mechanism deck section (CDM37LH-5BD29AL)
  • Page 10 TAPE MECHANISM DECK SECTION (TCM-220WR2) 4 three screws 4 three screws (BVTP2.6 × 8) (BVTP2.6 × 8) 3 wire (flat type) 5 Remove the tape mechanism deck section (21 core) (CN601) (TCM-220WR2) to direction of the arrow A . 3 wire (flat type) (11 core) (CN1001) 2 Open the cassette lids.
  • Page 11 CD LID ASS’Y SECTION 6 four screws (BVTP2.6 × 8) 5 connector (CN671) 7 CD lid ass’y 4 connector (CN661) 2 four screws (BVTP2.6 × 8) 3 CD-B1 SW board 1 connector (CN642) PANEL (A) / (B) SUB ASS’Y 1 connector (CN612) 3 two claws 2 four screws...
  • Page 12 BASE UNIT 3 base unit 1 yoke bracket 2 boss DISC TABLE Note: When the disc table is installed, adjust the positions of roller cam and mark ( as shown in the figure, then set to the groove of disc table. 3 step screw 1 screw (BVTP3 ×...
  • Page 13 BD BOARD 1 two screws 1 two screws (PTPWH M2.6 × 8) (PTPWH M2.6 × 8) 2 optical pick-up section 3 two springs 3 two springs 5 screw (BVTP2.6 × 8) 4 wire (flat type) (16 core) (CN101) 7 BD board 6 Removal the four solders.
  • Page 14 AUDIO BOARD, CAPSTAN MOTOR (M1) 1 connector (CN651) 2 four screws (BTP2.6 × 4) 3 Removal the AUDIO board to direction of the arrow A . 5 two screws (BTP2.6 × 8) 7 Removal the capstan motor (M1) to direction of the arrow B . 4 Break the soldering of motor lead.

  • Page 15: Test Mode

    SECTION 4 TEST MODE [MC Cold Reset] [Change-over of AM Tuner Step between 9kHz and 10kHz] • The cold reset clears all data including preset data stored in the • A step of AM channels can be changed over between 9kHz and RAM to initial conditions.
  • Page 16 [Aging Mode] 2-2. Operation during Aging Mode This mode can be used for operation check of CD section and tape In the aging mode, the program is executed in the following se- deck section. quence. • If an error occurred: 1.

  • Page 17: Mechanical Adjustments

    SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION TAPE DECK SECTION 0 dB=0.775 V 1. Clean the following parts with a denatured-alcohol-moistened 1. Demagnetize the record/playback head with a head demagne- swab: tizer. (Do not bring the head demagnetizer close to the erase record/playback heads pinch rollers erase head...
  • Page 18 DECK A 1. Mode: Playback (FWD) Tape Speed Adjustment 2. Turn the adjustment screw and check output peaks. If the peaks Note: Start the Tape Speed adjustment as below after setting to the test mode. do not match for L-CH and R-CH, turn the adjustment screw In the test mode, the tape speed is high during pressing the so that outputs match within 1dB of peak.
  • Page 19 DECK B Record bias Current Adjustment Adjustment Location: Procedure: [MAIN BOARD] (Component Side) 1. Mode: Record Pin 6 (L-CH) of IC1501 on the MAIN board. RV1501 Pin #¶ (R-CH) of IC1501 on the MAIN board. CN207  1) 315 Hz IC1501 ...

  • Page 20: Cd Section

    S Curve Check CD SECTION oscilloscope Note: 1. CD Block is basically designed to operate without adjustment. There- BD board fore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (FEO) 3. Use an oscilloscope with more than 10M impedance. TP (VC) –...
  • Page 21 E-F Balance (1 Track Jump) check Adjustment Location: (Without remote commander) [BD BOARD] (Conductor Side) oscilloscope BD board TP (TEO) TP (VC) – IC101 Procedure: 1. Connect oscilloscope to test point TP (TEO) on BD board. 2. Turned Power switch on. 3.

  • Page 22: Diagrams

    SECTION 7 DIAGRAMS 7-1. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC301 µPD780018YGF-028-3BA (SYSTEM CONTROLLER) Pin No. Pin Name Function TA-MUTE Line muting on/off control signal output terminal “L”: muting on DBFB normal/high selection signal output to the M62427FP (IC201) DBFB-H/L “L”: DBFB high, “H”: DBFB low 427-LAT...
  • Page 23 Pin No. Pin Name Function COM-DOUT Serial data output to the M62427FP (IC201) COM-CLK Serial data transfer clock signal output to the M62427FP (IC201) Power on/off control signal output for the CD mechanism deck section CD-POWER “H”: power on, “L”: standby CD-DATA Serial data output to the CXD2519Q (IC103) CD-CLK...
  • Page 24 Pin No. Pin Name Function CAP-M-ON/OFF Capstan motor (M1) on/off control signal output terminal “L”: capstan motor on PB-A/B Deck-A/B selection signal output to the HA12203NT (IC1501) “L”: deck-A, “H”: deck-B Normal/high speed selection signal output to the HA12203NT (IC1501) EQ-H/N “L”: normal speed, “H”: high speed Recording bias on/off selection signal output to the HA12203NT (IC1501)
  • Page 25 • PANEL BOARD IC601 TMP87CH75F-6659 (FLUORESCENT INDICATOR TUBE DRIVE, LED DRIVE, KEY CONTROL) Pin No. Pin Name Function Pin No. Pin Name Function SEG-35 Segment drive signal output to the fluorescent indicator tube (FL601) Key input terminal (A/D input) (S641 to 647, 661 to 666) KEY-5 DECK A ·/ª/p/0/), DOLBY NR, DIRECTION, DIRECT PLAY DISC 1/2/3/4/5, DJ V-LOAD...

  • Page 26: Block Diagram - Cd Section

    HCD-XB66/XB660 7-2. BLOCK DIAGRAM – CD Section – DIGITAL SIGNAL PROCESSOR, FILTER CLV SERVO PROCESSOR, DIGITAL FILTER, D/A CONVERTER IC103 PD1 I-V AMP PCMDI PCMD OVER SERIAL BCKI SAMPLING INPUT DIGITAL LRCK LRCKI DETECTOR INTERFACE ASYMMETRY FILTER SUMMING DIGITAL PLL...

  • Page 27: Block Diagram - Tape Deck Section

    HCD-XB66/XB660 7-3. BLOCK DIAGRAM – TAPE DECK Section – DECK PROCESS DECK A/B SELECT, PB/REC EQ AMP, DOLBY NR AMP • SIGNAL PATH IC1501 : PLAYBACK (DECK A) HP101 DOLBY PASS (PLAYBACK) : PLAYBACK (DECK B) PB OUT (L) PB-L...

  • Page 28: Block Diagram - Main Section (1/2)

    HCD-XB66/XB660 7-4. BLOCK DIAGRAM – MAIN Section (1/2) – J761 MIX MIC (Page 30) • SIGNAL PATH REC-L MIC AMP MIC AMP : CD PLAY IC760 (1/2) IC760 (2/2) : TAPE PLAY RV760 J101 (2/2) MIC LEVEL : RECORD VIDEO/MD...

  • Page 29: Block Diagram - Main Section (2/2)

    HCD-XB66/XB660 7-5. BLOCK DIAGRAM – MAIN Section (2/2) – J760 PHONES • SIGNAL PATH : CD PLAY L-CH L-CH (+) POWER AMP IC801 (1/2) TM131 (Page 32) – SPEAKER IMPEDANCE USE 8 – 16Ω – L-CH (–) POWER AMP IC801 (2/2)

  • Page 30: Block Diagram - Display/Key Control/Power Supply Section

    HCD-XB66/XB660 7-6. BLOCK DIAGRAM – DISPLAY/KEY CONTROL/POWER SUPPLY Section – FLUORESCENT INDICATOR TUBE DRIVE, LED DRIVE, KEY CONTROL IC601 DATA, CLK DATA POWER DATA (Page 31) CLOCK (Page 31) FLUORESCENT INDICATOR TUBE FL601 CD-POWER (Page 31) RESET RESET (Page 32)
  • Page 31 • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) TRANS board Note on Schematic Diagram: Note on Printed Wiring Boards: • X : parts extracted from the component side. •...

  • Page 32: Printed Wiring Board - Cd Section (1/2)

    HCD-XB66/XB660 7-7. PRINTED WIRING BOARD – CD Section (1/2) – • • See page 37 for Circuit Boards Location. See page 38 for Note. • Semiconductor Location Ref. No. Location IC101 IC201 IC501 Q101 MAIN BOARD CN202 (Page 51) – 39 –...

  • Page 33: Schematic Diagram - Cd Section (1/2)

    HCD-XB66/XB660 7-8. SCHEMATIC DIAGRAM – CD Section (1/2) – • • • See page 38 for Note. See page 77 for Waveforms. See page 78 for IC Block Diagrams. The components identified by mark ! or dotted line with mark ! are critical for safety.

  • Page 34: Printed Wiring Boards - Cd Section (2/2)

    HCD-XB66/XB660 7-9. PRINTED WIRING BOARDS – CD Section (2/2) – • See page 37 for Circuit Boards Location. • See page 38 for Note. TABLE SENSOR BOARD CD MOTOR BOARD (DISC TRAY TURN) BD LED MAIN BOARD BOARD CN203 (PAGE 51)

  • Page 35: Schematic Diagram - Cd Section (2/2)

    HCD-XB66/XB660 7-10. SCHEMATIC DIAGRAM – CD Section (2/2) – • See page 38 for Note. • See page 80 for IC Block Diagrams. • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : STOP...

  • Page 36: Printed Wiring Boards - Tape Deck Section

    HCD-XB66/XB660 7-11. PRINTED WIRING BOARDS – TAPE DECK Section – • See page 37 for Circuit Boards Location. • See page 38 for Note. (PAGE 51) MAIN BOARD MOTOR CN205 BOARD AUDIO BOARD CN651 (DECK B PLAY) (DECK A PLAY)

  • Page 37: Schematic Diagram - Tape Deck Section

    HCD-XB66/XB660 7-12. SCHEMATIC DIAGRAM – TAPE DECK Section – • See page 38 for Note. • See page 80 for IC Block Diagrams. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

  • Page 38: Printed Wiring Board - Main Section

    HCD-XB66/XB660 7-13. PRINTED WIRING BOARD – MAIN Section – • See page 37 for Circuit Boards Location. • See page 38 for Note. • Semiconductor Location Ref. No. Location D141 G-11 D142 I-10 D191 F-12 D192 F-12 D291 D301 D302...

  • Page 39: Schematic Diagram - Main Section (1/3)

    HCD-XB66/XB660 7-14. SCHEMATIC DIAGRAM – MAIN Section (1/3) – • • See page 38 for Note. See page 77 for Waveforms. • Voltages and waveforms are dc with respect to ground ) : VIDEO/MD (AUDIO) 〈〈 〉〉 : PLYABACK under no-signal (detuned) conditions.

  • Page 40: Schematic Diagram - Main Section (2/3)

    HCD-XB66/XB660 7-15. SCHEMATIC DIAGRAM – MAIN Section (2/3) – • • See page 38 for Note. See page 80 for IC Block Diagrams. • Voltages and waveforms are dc with respect to ground The components identified by mark ! or dotted line under no-signal (detuned) conditions.

  • Page 41: Schematic Diagram - Main Section (3/3)

    HCD-XB66/XB660 7-16. SCHEMATIC DIAGRAM – MAIN Section (3/3) – • See page 38 for Note. • See page 80 for IC Block Diagrams. • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : PLAYBACK ) : RECORD –...

  • Page 42: Printed Wiring Board - Power Amp Section

    HCD-XB66/XB660 7-17. PRINTED WIRING BOARD – POWER AMP Section – • See page 37 for Circuit Boards Location. • See page 38 for Note. • Semiconductor Location Ref. No. Location D800 D801 D811 D821 D831 D841 D842 D851 D871 D891...

  • Page 43: Schematic Diagram - Power Amp Section

    HCD-XB66/XB660 7-18. SCHEMATIC DIAGRAM – POWER AMP Section – • See page 38 for Note. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.

  • Page 44: Printed Wiring Board - Panel Section (1/3)

    HCD-XB66/XB660 7-19. PRINTED WIRING BOARD – PANEL Section (1/3) – • See page 37 for Circuit Boards Location. • See page 38 for Note. • Semiconductor Location Ref. No. Location D601 D602 D-10 D603 D604 D605 B-10 D606 D607 D611...

  • Page 45: Schematic Diagram - Panel Section (1/3)

    HCD-XB66/XB660 7-20. SCHEMATIC DIAGRAM – PANEL Section (1/3) – • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. • See page 38 for Note. no mark : FM – 65 – – 66 –...

  • Page 46: Printed Wiring Boards - Panel Section (2/3)

    HCD-XB66/XB660 7-21. PRINTED WIRING BOARDS – PANEL Section (2/3) – • See page 37 for Circuit Boards Location. • See page 38 for Note. – 67 – – 68 –...

  • Page 47: Schematic Diagram - Panel Section (2/3)

    HCD-XB66/XB660 7-22. SCHEMATIC DIAGRAM – PANEL Section (2/3) – • See page 38 for Note. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM – 69 – – 70 –...

  • Page 48: Printed Wiring Boards - Panel Section (3/3)

    HCD-XB66/XB660 7-23. PRINTED WIRING BOARDS – PANEL Section (3/3) – • • See page 37 for Circuit Boards Location. See page 38 for Note. – 71 – – 72 –...

  • Page 49: Schematic Diagram - Panel Section (3/3)

    HCD-XB66/XB660 7-24. SCHEMATIC DIAGRAM – PANEL Section (3/3) – • See page 38 for Note. – 73 – – 74 –...

  • Page 50: Printed Wiring Board - Power Supply Section

    HCD-XB66/XB660 7-25. PRINTED WIRING BOARD – POWER SUPPLY Section – 7-26. SCHEMATIC DIAGRAM – POWER SUPPLY Section – • See page 37 for Circuit Boards Location. • See page 38 for Note. • See page 38 for Note. The components identified by mark ! or dotted line with mark ! are critical for safety.
  • Page 51 • Waveforms – CD Section (1/2) – – MAIN Section (1/3) – 1 IC101 #£ (RF_O) (PLAY MODE) 6 IC103 ^™ (RFCK) 1 IC301 !¡ (X1) Approx. 1.3 Vp-p 5.6 Vp-p 4.3 Vp-p 135.5 µ s 200 ns 2 IC301 !¢ (XT1) 2 IC101 2 (FEI) (PLAY MODE) 7 IC103 &¢...

  • Page 52: Ic Block Diagrams

    • IC Block Diagrams – BD Board – IC101 CXA1992AR – RF SUMMING PD2 IV PD1 IV FE_BIAS SENS2 ↓ SENS1 – LASER POWER CONTROL F IV AMP FE AMP C. OUT – E IV AMP – DFCT XRST – LEVEL S DATA FO.
  • Page 53 IC102 BA5941FP-E2 – + – + – LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT – LEVEL SHIFT – – + – – + – MUTE IC103 CXD2591Q 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 LRCK AVSS WDCK...

  • Page 54: Main Board

    – CD MOTOR Board – IC201 TA8409S VREF BLOCK STANDBY BLOCK HEAT CUT OFF BLOCK OUT2 OUT1 VREF – MAIN Board – IC281 µPC1237HA IC901 LA5617 OVER LOAD DET CURRENT CURRENT START ON/OFF ON/OFF LIMITER LIMITER CIRCUIT MUTE OFFSET DET VREF VMUTE OVER HEAT...

  • Page 55: Exploded Views

    SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 56 (2) FRONT PANEL SECTION-1 TCM-220WR2 supplied supplied supplied with S711 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-987-995-01 SPRING (CD EJECT), COMPRESSION 4-987-000-12 BUTTON (EJECT B) 4-987-001-11 BUTTON (EJECT CD) * 66 1-664-013-11 TC-B SW BOARD * 53 1-664-019-11 CD-A SW BOARD * 67...
  • Page 57 (3) FRONT PANEL SECTION-2 supplied with J761 supplied supplied with RV760 supplied with J760 supplied supplied with S701 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4949-292-1 PANEL ASSY (XB66) * 110 A-4392-452-A HP/MIC BOARD, COMPLETE X-4949-613-1 PANEL ASSY (XB660) 4-986-990-11 BUTTON (CURSOR) 4-948-236-21 CUSHION (107)
  • Page 58 (4) CHASSIS SECTION not supplied not supplied T901 not supplied supplied E, MX CDM37LH-5BD29AL SA, AR not supplied not supplied The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref.
  • Page 59 (5) TAPE MECHANISM DECK SECTION-1 (TCM-220WR2) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-959-229-11 DETENT, CASSETTE 3-354-963-01 DAMPER X-4947-943-1 HOLDER (L) ASSY, CASSETTE * 207 4-980-439-01 FULCRUM, HOLDER X-4947-944-1 HOLDER (R) ASSY, CASSETTE 3-354-957-01 JOINT (LOCK LEVER) 4-959-231-11 SPRING (L), TORSION 3-354-953-01 LEVER (LOCK LEVER L)
  • Page 60 (6) TAPE MECHANISM DECK SECTION-2 (TCM-220WR2)  including r C    r C refer to next page. not supplied HP101 (including r A) not supplied not supplied HRPE101 (including r B) not supplied not supplied not supplied not supplied Ref.
  • Page 61 (7) TAPE MECHANISM DECK SECTION-3 (TCM-220WR2) rC: MOTOR board (supplied with AUDIO board) (refer to front page.) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-908-597-01 CAM (A) 3-908-600-01 LEVER (REV-B) 3-908-608-11 SCREW, STEP * 316 1-650-669-11 LEAF SWITCH BOARD X-3372-930-1 ARM (A) ASSY, FR...
  • Page 62 (8) CD MECHANISM DECK SECTION (CDM37LH-5BD29AL) not supplied M201 BU-5BD29AL supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-987-976-01 SCREW, STEP 4-978-426-01 INDICATOR (NO.) 4-944-490-01 BELT (TIMING) * 366 1-659-059-13 BD LED BOARD A-4660-978-A GEAR (PULLEY) ASSY * 367 1-659-058-13 TABLE SENSOR BOARD 4-978-421-01 GEAR (MID)
  • Page 63 (9) BASE UNIT SECTION (BU-5BD29AL) M101 M102 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ! 401 8-820-020-01 OPTICAL PICK-UP KSS-213D/Q-NP...

  • Page 64: Electrical Parts List

    SECTION 9 AUDIO ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 65 AUDIO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C126 1-163-038-91 CERAMIC CHIP 0.1uF R601 1-249-409-11 CARBON 1/4W R602 1-249-409-11 CARBON 1/4W C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V R608 1-249-409-11 CARBON 1/4W C128 1-163-135-00 CERAMIC CHIP 560PF R609 1-249-433-11 CARBON...
  • Page 66 BD LED CD MOTOR CD-A SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R105 1-216-088-00 METAL CHIP 1/10W R106 1-216-088-00 METAL CHIP 1/10W < SWITCH > R107 1-216-088-00 METAL CHIP 1/10W S101 1-572-085-11 SWITCH, LEAF (LIMIT) R108 1-216-088-00 METAL CHIP 1/10W...
  • Page 67 CD-A SW CD-B1 SW CD-B2 SW DOOR SW HP/MIC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > < SWITCH > R731 1-249-411-11 CARBON 1/4W S681 1-554-303-21 SWITCH, TACTILE ()) R732 1-249-413-11 CARBON 1/4W S682 1-554-303-21 SWITCH, TACTILE (REPEAT) R733...
  • Page 68 HP/MIC LEAF SWITCH MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > < RESISTOR > R791 1-249-412-11 CARBON 1/4W R760 1-249-429-11 CARBON 1/4W ************************************************************ R761 1-249-417-11 CARBON 1/4W R764 1-249-441-11 CARBON 100K 1/4W A-4403-844-A MAIN BOARD, COMPLETE R765 1-249-417-11 CARBON...
  • Page 69 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C253 1-130-493-00 MYLAR 0.068uF C1506 1-126-964-11 ELECT 10uF C254 1-130-493-00 MYLAR 0.068uF C1507 1-126-960-11 ELECT C255 1-130-486-00 MYLAR 0.018uF C256 1-130-486-00 MYLAR 0.018uF C1508 1-126-933-11 ELECT 100uF C257 1-130-480-00 MYLAR 0.0056uF 5%...
  • Page 70 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q1531 8-729-801-93 TRANSISTOR 2SD1387 < FERRITE BEAD > Q1532 8-729-029-66 TRANSISTOR DTC114ESA FB302 1-412-473-21 INDUCTOR 0uH Q1533 8-729-029-66 TRANSISTOR DTC114ESA Q1534 8-729-119-77 TRANSISTOR 2SA1175-FEK < IC > Q1535 8-729-029-66 TRANSISTOR DTC114ESA IC101...
  • Page 71 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R212 1-247-826-00 CARBON 1/4W R322 1-249-425-11 CARBON 4.7K 1/4W R213 1-249-429-11 CARBON 1/4W R323 1-247-807-31 CARBON 1/4W R214 1-249-437-11 CARBON 1/4W R215 1-247-903-00 CARBON 1/4W R324 1-247-891-00 CARBON 330K 1/4W R216...
  • Page 72 MAIN PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1504 1-247-840-00 CARBON 2.4K 1/4W C604 1-126-960-11 ELECT R1505 1-247-863-91 CARBON 1/4W C606 1-126-960-11 ELECT R1506 1-249-421-11 CARBON 2.2K 1/4W C608 1-126-382-11 ELECT 100uF 6.3V R1507 1-249-428-11 CARBON 8.2K 1/4W...
  • Page 73 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D615 8-719-058-04 DIODE SEL5223S-TP15 (SUPER WOOFER) R613 1-249-401-11 CARBON 1/4W D616 8-719-058-04 DIODE SEL5223S-TP15 (EFFECT) R614 1-249-429-11 CARBON 1/4W D617 8-719-058-04 DIODE SEL5223S-TP15 (ENTER) R615 1-249-429-11 CARBON 1/4W D618 8-719-058-04 DIODE SEL5223S-TP15 (FILE 1)
  • Page 74 PANEL POWER AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R678 1-249-415-11 CARBON 1/4W < VIBRATOR > R679 1-249-419-11 CARBON 1.5K 1/4W X601 1-579-125-11 VIBRATOR, CERAMIC (8MHz) R681 1-249-429-11 CARBON 1/4W ************************************************************ R682 1-249-421-11 CARBON 2.2K 1/4W R683...
  • Page 75 POWER AMP TABLE SENSOR TC-A SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > R841 1-249-421-11 CARBON 2.2K 1/4W R842 1-249-429-11 CARBON 1/4W CN801 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P R843 1-247-887-00 CARBON 220K 1/4W R844...
  • Page 76 TC-A SW TC-B SW TRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R706 1-249-403-11 CARBON 1/4W 1-668-169-11 TRANS BOARD R707 1-247-807-31 CARBON 1/4W ************ R708 1-249-407-11 CARBON 1/4W R709 1-249-407-11 CARBON 1/4W < CONNECTOR > R710 1-247-815-91 CARBON 1/4W...
  • Page 77 Ref. No. Part No. Description Remark M101 X-4917-504-1 MOTOR ASSY (SPINDLE) M102 X-4917-523-4 MOTOR ASSY (SLED) M201 A-4660-977-A MOTOR ASSY (TABLE) ! T901 1-431-638-11 TRANSFORMER, POWER ************************************************************ ************** HARDWARE LIST ************** 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S 7-685-871-01 SCREW +BVTT 3X6 (S) 7-685-872-09 SCREW +BVTT 3X8 (S) 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3 7-685-862-09 SCREW +BVTT 2.6X6 (S)
  • Page 78 HCD-XB66/XB660 Sony Corporation 98C057025-1 Printed in Singapore © 1998. 3 9-922-769-11 Home A&V Products Company Published by General Engineering Dept. – 104 – (Shibaura)

This manual is also suitable for:

Hcd-xb660

Table of Contents