Page 1
HCD-XB88AVK/XB88K SERVICE MANUAL E Model HCD-XB88AVK/XB88K is the tuner, deck, CD and amplifier section in LBT-XB88AVK/XB88K. Photo: HCD-XB88AVK Model Name Using Similar Mechanism HCD-D670AV/N555AV CD Mechanism Type CDM37L-5BD29AL CDM37LH-5BD29AL SECTION Base Unit Type BU-5BD29AL Optical Pick-up Type KSS-213D/Q-NP TAPE Model Name Using Similar Mechanism...
Page 2
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. : Singapore model REPLACE THESE COMPONENTS WITH SONY PARTS MY : Malaysia model TH : Thai model WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS : Indonesian model MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 –...
TABLE OF CONTENTS 1. GENERAL 7. EXPLODED VIEWS ................4 7-1. Case and Back Panel Section ..........90 7-2. Front Panel Section 1 ............91 2. DISASSEMBLY 7-3. Front Panel Section 2 ............92 2-1. Front Panel ................6 7-4. Chassis Section ..............93 2-2.
SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. FRONT PANEL 1 Three flat type wiers (CN401,CN402,CN701) 3 Front panel 2 Four screws (BVTP3x8) 2-2. MAIN BOARD 4 Back panel 3 Power cord 2 Thirteen screws (BVTP3x8) 1 Flat type wire (CN1) 9 Main board !º...
2-3. TAPE MECHANISM DECK 4 Three screws (BVTP2.6x8) 3 Three screws (BVTP2.6x8) 5 Remove the tape mechanism deck section to direction of arrow A . 2 Open the cassette lid. 1 Push the two buttons. 2-4. CASSETTE LID ASSEMBLY 3 Two brackets. 2 Two screws (BVTP2.6x8) 1 Two springs.
2-5. CD LID ASSEMBLY 1 Four screws (BVTP2.6x8) 2 Connector (CN671) 4 CD lid assembly 3 Connector (CN661) 2-6. CD MECHANISM DECK 2-7. BASE UNIT 1 Five screws (BVTP3x8) 2 CD mechanism deck 3 Base unit 2 Boss 1 Yoke bracket –...
2-8. DISC TABLE NOTE: When the disc table is installed, adjust the positions of roller cam and mark ” as shown in the figure, then set to the groove of disc table. 4 Stop screw 2 Screw (BVTP3X8) 1 Screw (BVTP3X8) 3 Bracket (BU) 5 Disc table –...
SECTION 3 SERVICE MODE MC Cold Reset • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press three buttons SPECTRUM ANALYZER , ENTER , and DISC 1 simultaneously. 2.
Page 11
Aging Mode This mode can be used for operation check of CD section and tape deck section. • If an error occurred: The aging operation stops. • If no error occurs: The aging operation continues repeatedly. 1. Aging Mode in CD Section 1-1.
SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head damagnetizer. record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments. erase head rubber belts 3.
Page 13
2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment (Deck A) do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak. Note: Set the test mode using the following method and begin tape speed adjustment.
Page 14
Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B) Procedure: Procedure: INTRODUCTION INTRODUCTION When set to the test mode performed in Tape Speed Adjust- When set to the test mode performed in Tape Speed Adjust- ment, when the tape is rewound after recording, the “REC memory ment, when the tape is rewound after recording, the “REC memory mode”...
Page 15
E-F Balance (1 Track Jump) check CD SECTION oscilloscope Note: BD board 1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given. TP (TEO) 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (VC) 3.
HCD-XB88AVK/XB88K – DECK SECTION – PB A/B S1004 S1008 B CrO A CrO CN403 R CH RV311 PLAYBACK IC611 A 120/70 PB-A/B B 120/70 LEVEL DECK A A IN PB OUT B IN PB L HP101 PB HEAD R CH...
HCD-XB88AVK/XB88K – MAIN SECTION – VOLUME DOLBY PRO LOGIC IC604 DELAY IC601 CENTER REAR IC602 KEY CON IC603 MUTE REAR L IN SECTION C-OUT REAR REAR Q602 S-OUT DATA S-OUT S-IN L-IN L-OUT FRONT LATCH FRONT CENTER DATA L-MIX J101...
HCD-XB88AVK/XB88K TM402 SURROUND – POWER SECTION – POWER AMP SPEAKER IC601 REAR RY401 REAR –1 REAR REAR CENTER –2 CENTER CENTER CENTER RELAY DRIVE Q404 FAN MOTOR M901 DRIVER UNREG Q961, 962 MOTOR –12V OVER LOAD Q601,651 THERMAL TM401 POWER AMP...
HCD-XB88AVK/XB88K – KEY CON SECTION – MIC AMP ECHO AMP IC760 (2/2) IC760 (1/2) J761 MIC 1 RV760 MIC LEVEL ECHO IC761 J762 MIC 2 RV761 LPF1 LPF2 ECHO LEVEL SWITCH IC1403 L IN 9 10 11 KEY CONTROL IC1401...
Page 22
WAVEFORMS THIS NOTE IS COMMON FOR PRINTED WIRING – CD SECTION – – MAIN SECTION (1/5) – BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) 1.3Vp-p 4.8Vp-p For schematic diagrams. Note: 8MHz 500mV/DIV, 500nsec/DIV •...
HCD-XB88AVK/XB88K 6-6. SCHEMATIC DIAGRAM – CD SECTION – • See page 28 for Waveforms. • See page 77 for IC Block Diagrams. • See page 82 for IC Pin Functions. (Page 40) – 33 – – 34 –...
HCD-XB88AVK/XB88K 6-9. SCHEMATIC DIAGRAM – MAIN (2/5) SECTION – • See page 28 for Waveforms. • See page 35 for Printed Wiring Board. • See page 88 for IC Pin Functions. – 39 – – 40 –...
6-29. IC BLOCK DIAGRAMS • CD section IC101 CXA1992AR – RF SUMMING PD2 IV PD1 IV FE_BIAS SENS2 ↓ – SENS1 LASER POWER CONTROL F IV AMP FE AMP – C. OUT E IV AMP – DFCT XRST – LEVEL S DATA FO.
Page 49
• Main section IC102 MC14052BCP IC103, 1403, 1702 MC14053BCP B.COM OPEN A.COM C.COM OPEN OPEN IC402 LB1641 T.S.D O.C.P MOTOR MOTOR DRIVE DRIVE FWD/REV/STOP CONTROL LOGIC IC602 LV1016 INV-PHASE ADM-CONT SRAM L+DELAY R+DELAY VOL/MUTE OUT-FILTER – DC-OUT IN-FILTER (7k/5k) (40kHz) L–R S-TRIM (–6dB)
Page 50
IC601 LA2786 BPF1 NOISE NOISE FILTER BPF2 NOISE GENERATOR DATA BALANCE ENABLE VREF V REF CONTROL OSC1 DIVIDER CONTROL S-CH DC OUT C-CH DC OUT L-CH DC OUT R-CH DC OUT VREF L-IN L-OUT R-IN R-OUT S-OUT C-OUT CMODE-CAP. C-TRIM DC CUT R-BPF1 L-BPF1 L-BPF2...
Page 51
• CD motor sectoin • KEY CON sectoin IC201 TA8409S IC1403 BU4053BC VREF B.COM BLOCK STANDBY OPEN BLOCK A.COM C.COM OPEN OPEN HEAT CUT OFF BLOCK OUT2 OUT1 VREF IC1401 M65847FP • Power sectoin IC301 uPC1237HA OVER LOAD DET – –...
6-30. IC PIN FUNCTIONS • IC101 FOCUS/TRACKING/SLED SERVO RF AMP (CXA1992AR) Pin Name Function Pin No. Focus error amplifier output Connected internally to the window comparator input for bias adjustment Focus error input Capacitor connection pin for defect time constant FDFCT Ground this pin through a capacitor for cutting the focus servo high-frequency gain External time constant setting pin for boosting the focus servo low-frequency...
Page 53
Pin No. Pin Name Function RF summing amplifier inverted input The RF amplifier gain is determined by the resistance connected between this pin and RF M RFO pin RFTC External time constant setting pin during RF level control APC amplifier output APC amplifier input RF I-V amplifier inverted input Connect these pins to the photo diode A+C and B+D pins...
Page 54
• IC103 DIGITAL SIGNAL PROCESSOR (CXD2519Q) Pin No. Pin Name Function – +5V power supply – Ground Lch “L” detection flog (Not used) LMUT Rch “L” detection flog (Not used) RMUT Test output (Not used) ACDT Master clock divider output (Not used) CKOUT Clock input for SQSO read out SQCK...
Page 55
Pin No. Pin Name Function Analog ground AVSS – CLTV Control voltage input for VCO AVDD Analog power supply – EFM signal input BIAS Asymmetry circuit constant current input Asymmetry comparate voltage input ASYI EFM full swing output (“L” =V , “H”...
Page 56
Pin Name Function Pin No. — Not used – AVSS Analog ground – AVDD Analog power supply – AOUT1 Lch analog output AIN1 Lch opamp input LOUT1 Lch line output AVSS Analog ground – XVDD – Master clock power supply XTAI X’tal oscillator circuit input XTAO...
Page 57
• IC601 DISPLAY CONTROL (TMP87CH75F-6559) Pin Name Function Pin No. SEG35 FL segment signal output VLOAD – Power supply (–25V) for FL segment signal output 3 to 10 LED1 to LED8 LED driver output – Ground X-OUT X’tall (8MHz) X-IN RESET Reset signal input from main controller LED 9...
Page 58
• IC701 MASTER CONTROL (uPD780018YGF-028-3BA) Pin Name Function Pin No. TA-MUTE Line mute signal output DBFB-H/L DBFB H/L select signal output 427-LT Latch signal output for IC201 (62427) KCON-LT Latch signal output for key control KCON-ON Key control ON/OFF signal output F-RELAY Front speaker relay control output (Not used) R-RELAY...
Page 59
Pin Name Function Pin No. MSM-LT MSM-NAR Not used MSM-CH INPUT-CHANGE Input sensitivity switching output IIC-DATA Data output for IC601 IIC-CLK Clock output for IC601 XRST CD reset signal output CD latch signal output FOUCUS-SW Not used TBL-L Table motor control output TBL-R TRAY-LED CD tray LED ON/OFF output...
SECTION 7 EXPLODED VIEWS NOTE: • Abbreviation The components identified by : Saudi Arabia model • Items marked “*” are not stocked since they are mark ! or dotted line with mark : Singapore model seldom required for routine service. Some delay ! are critical for safety.
7-4. CHASSIS SECTION not supplied T501 (XB88K) T901 (XB88AVK) not supplied not supplied (SP,MY,EA) CDM37L-5BD29AL CDM37LH-5BD29AL CNP901 CNP901 (E,IA,TH) (E,IA) not supplied The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref.
7-6. TC MECHANISM SECTION-2 (TCM-220WR2) (including p A) not supplied HP101 (includeing r A) not supplied not supplied HRPE101 (including r B) not supplied not suppl ied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-908-560-01 SPRING, AZIMUTH ADJUSTMENT...
7-9. BASE UNIT SECTION (BU-5BD29AL) M101 M102 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ! 401 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP...
SECTION 8 AUDIO ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark diagrams or the components used on the set.
Page 70
AUDIO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R612 1-249-409-11 CARBON 1/4W F C131 1-164-346-11 CERAMIC CHIP ! R621 1-212-851-00 FUSIBLE 1/4W F ! R622 1-212-851-00 FUSIBLE 1/4W F C140 1-110-501-11 CERAMIC CHIP 0.33uF R623 1-249-432-11 CARBON 1/4W C154...
Page 71
CD-A SW CD-B1 SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R105 1-216-088-00 METAL CHIP 1/10W R191 1-216-105-91 RES,CHIP 220K 1/10W R106 1-216-088-00 METAL CHIP 1/10W R107 1-216-088-00 METAL CHIP 1/10W < SWITCH > R108 1-216-088-00 METAL CHIP 1/10W S101...
Page 72
CD-B2 SW CD-LED CD MOTOR DOOR SW HP/MIC CD-B1 SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < SWITCH > < IC > S676 1-554-303-21 SWITCH, TACTILE (·) IC201 8-759-365-94 IC TA8409S S677 1-554-303-21 SWITCH, TACTILE (p) S678 1-554-303-21 SWITCH, TACTILE (P) <...