Panasonic KX-FT937LA-B Service Manual page 58

KX-FT937LA-B
Code Function
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
710 Memory clear except History data
717 Transmit speed selection
718 Receive speed selection
722 Redial tone detect
731 CPC mode
732 AUTO disconnect cancel time
745 Power ON film feed
763 CNG detect time for friendly reception
774 T4 timer
775 Monitoring of message transfer
784 Voice Prompt Test
815 Sensor check
841 Digital SP-Phone check
852 Print test pattern
853 Top margin
874 DTMF on time
875 DTMF off time
880 History list
881 Journal 2 list
882 Journal 3 list
961 The time transmitting the false ring back
tone
962 The operator calling time
Set Value Effective
Range
1:OFF 1~3
2:ALL
3:AUTO
1:75 msec 1~3
2:500 msec
3:1 sec
1: detects at 1, 2
the 1st time
2: detects at
the 2nd time
1: 5 % 1~4
2: 10 %
3: 15 %
4: 20 %
10 = -10 dBm 00~15
43 = -43 dBm 20~48
1:9600BPS 1~4
2:7200BPS
3:4800BPS
4:2400BPS
1:9600BPS 1~4
2:7200BPS
3:4800BPS
4:2400BPS
1:ON 2:OFF 1, 2
1:A 2:B 3:OFF 1, 2, 3
1:350 ms 1~3
2:1.8 sec
3:OFF
1:ON 2:OFF 1, 2
1:10 sec 1, 2, 3
2:20 sec
3:30 sec
X 100 msec 00~99
1:ON 2:OFF 1, 2
1~9
X 10 msec 06~20
X 10 msec 06~20
X sec 01~10
X sec 05~30
58
Default
2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.81).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.83). Refer to Receive
Problem (P.82) and The unit can copy, but cannot
transmit/receive (P.83).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.83). Refer to Sometime
there is a transmit problem (P.81) and The unit can
copy, but cannot transmit/receive (P.83).
2 Sets the number of acceptable error lines when the
FAX reconstructs the received data. Refer to Receive
Problem (P.82).
10 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.81) and Receive Prob-
lem (P.82).
42 Used when there is an error problem. Refer to The unit
can copy, but cannot either transmit/receive long
distance or international communications (P.84).
Refer to Memory Clear Specification (P.59).
1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.81) and The unit can copy, but the transmission
and reception image are incorrect (P.86).
1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.82) and The unit
can copy, but the transmission and reception image
are incorrect (P.86).
1 Sets the tone detection mode after redialing.
1 Set the CPC signal detection mode from the converter.
1 "Set to "2" when the auto disconnect circuit operates.
and cuts the line."
1 Invalid function for thermal model.
3 Selects the CNG detection tone of friendly reception.
00 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
2 If set to ON a message can be monitored from this
unit's SP-PHONE when transferring a message.
000 See Test Mode (P.54).
See Test Mode (P.54).
See Digital Speakerphone (P.145).
See Test Mode (P.54).
3 ----------
10 ----------
10 ----------
----------
See Special service journal reports (P.76).
See Special service journal reports (P.76).
05 Set the time transmitting the false ring back tone to the
line in TEL/FAX mode.
13 Set the operator calling time through the speaker in
TEL/Fax mode.
Remarks