Fig. C Fig. A On the rear glass the data electrode is mounted. Toshiba 50 wide plasma display panel is develope for large The dielectric is coated on the rear glass. screen multimedia display with space saving. Red, Green and Blue colour phosphors are formed on the data The plasma display panel use AC type Sub-field drive system electrode with the ribs.
1.5. Pixel Structure 1.7. Initialization Fig. E Fig. G 50 inch plasma display panel has 1,049,088 pixels. To clear any remaining electric charge into the pixel, trapezoid Each pixels structure is shown fig. E. voltage is applied between the scan and sustain electrodes. 1.6.
1.9. Wall Voltage 1.11. Sustain Step 2 Fig. I Fig. K When input pulses are stopped, Ions and Electrons which are When sustain pulse is stopped, Ions and Electrons are charged on the dielectric around the electrodes are remained. remained again as Wall voltage. However polarity of wall voltage is reversed.
1.13. Sustain Step 4 1.15. Repeat Step 1 to Step 5 Fig. M Fig. O When sustain pulse is stopped, Ions and Electrons are To keep discharge continuously step 1 to 5 operation will be remained again as Wall voltage. However polarity of wall repeated.
1.17. Dual Scan 1.19. Real Black drive Fig. Q Fig. S The sustain period of sub-field drive system. Therefore For standard sub field drive, initialization discharge is done at brightness peak is limited. Because 768 horizontal lines each sub field. So that during one TV field period same sub scanning is carried out during address period.
2 Service Hint Baord name Function Board name Function Data drive (Upper Left) Panel drive power Data drive (Upper Center) Processing voltage control Data drive (Upper Right) PFC oscillator Data drive (Lower Left) High Voltage protect Data drive (Lower Center) Low Voltage protect Data drive (Lower Right) Regulator...
3 Adjustment Procedure 3.1. +B Set-up 3.2. Driver Set-up 3.1.1. Item / Preparation 3.2.1. Item / Preparation 1. Confirm the main voltage set switch Is set to 230V. (A, B, 1. Input an APL 100 % white signal. and E version) Confirm the main voltage set switch is set to 2.
3.5. Initialization Pulse Adjust 1. Input a Cross hatch signal. 2. Set the picture controls: - Picture mode: Normal White balance: Cool Adjust the indicated test point for the specified wave form. Test point Volume TPSC1 (SC) R6524 (SC) 20 ± 10µ Sec TPSC1 (SC) R6556 (SC) 160 ±...
4 Alignment Setting 4.1. How to access Alignment 1. Press and hold the Volume down / - button on the front panel of the unit and press the status [ + ] button on the remote control 3 times quickly within 1 second, this will place the unit into the CAT menu (Main service mode) 2.
5.3. NTSC panel white balance INPUT Equipment Setting Alignment menu Procedure 1 NTSC Color Picture: 1) Find the nearest area to brightness of 10 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 10 cd/m Cool exactly.
5.4. PAL/SECAM panel white balance INPUT Equipment Setting Alignment menu Procedure 1 PAL Color Picture: 1) Find the nearest area to brightness of 10 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 10 cd/m Cool exactly.
Page 19
Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm Cool R Drive Normal G Drive Warm B Drive R Cut off G Cut off B Cut off...
5.5. Pedestal setting INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 1 Component Picture: PANEL W/B (525i, 525p, 625i, Normal R cut off 1) Set R,G and B cut off to " 80 ". 720i or 1080i) White balance: G cut off Cool...
5.6. PC/RGB panel white balance INPUT Equipment Setting Alignment menu Procedure 1 PC Color Picture: 1) Find the nearest area to brightness of 10 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 10 cd/m Cool exactly.
Page 22
INPUT Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm R Drive Cool Gray Scale Normal G Drive Pattern Warm B Drive...
5.7. HD/ 525i /525p panel white balance INPUT Equipment Setting Alignment menu Procedure (720i or 1080i) Color Picture: 1) Find the nearest area to brightness of 10 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 10 cd/m...
Page 24
INPUT Equipment Setting Alignment menu Procedure Picture: 1) Write down each color temaparature of R,G,B drive and Normal Cut off data as follows. Aspect: 16:9 White White balance: Balance Cool Normal Warm R Drive Cool Gray Scale G Drive Normal Pattern Warm B Drive...
5.8. 625i panel balance INPUT Equipment Setting Alignment menu Procedure 1 625i Color Picture: 1) Find the nearest area to brightness of 10 cd/m as Low Gray Scale Analyzer Normal Sub Adjust light by color sensor. Pattern White balance: Sub Bright 2) Adjust Sub bright to set Low light level to 10 cd/m Cool exactly.
5.9. Sub brighness setting INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 1 NTSC Picture: PANEL W/B Gray Scale Normal All cut off 1) Set white balance to Cool . Pattern Aspect: 16:9 2) Adjust All cut off to start some pixels emission at black 2% area and no emission at black 0% area.
Page 27
INPUT Equipment Setting Alignment menu Procedure ** Adjust at the dark room. 4 525i Picture: PANEL W/B Gray Scale Normal All cut off 1) Set white balance to Cool . Pattern Aspect: 16:9 2) Adjust All cut off to start some pixels emission at black 2% area and no emission at black 0% area.
5.10. Pos./Size setting 1. Receive the test pattern signal which can be found the 5.14.1. Side panel color setting center and edge position and align properly. Colour of side panel which are left and right side blank area of Alignment Item Reference Setting/Special feature 4:3 aspect mode can be adjusted as desired color and...
6 Self Check 6.1. Display Indication 1. Self-check is used to automatically check the bus line controlled circuit of the Plasma display. 2. To get into the Self-check mode press the volume down button on the customer controls at the front of the set, at the same time pressing the OFF-TIMER button on the remote control, and the screen will show :- If the CCU ports have been checked and found to be incorrect...
7 Trouble shooting guide 7.1. No Power First check point There are following 3 states of No Power indication by power LED. 1. No lit 2. Green is lit then turns red blinking a few seconds later. 3. Only red is lit. 1.
7.2. No Picture 7.3. Local screen failure Plasma display may have local area failure on the screen. Fig - 1 is the possible defect P.C.B. for each local area. Fig - 1...
8 P.C.B. (Printed Circuit Board) exchange 8.1. Caution 1. To remove P.C.B. , wait 1 minute after power was off for discharge from electrolysis capacitors. 8.2. Quick adjustment after P.C.B. exchange P.C.B. Item Volume Test point Level P board Vsus R639 TPVsus (SS) Vsus ±...
10 Basic Circuit Explanation 10.1. Power Supply Circuit 10.1.1. Power Factor Control (PFC) 10.1.1.1. Basic operation of the Full wave bridge rectifier Feature: 1. Power Factor 05~0.7 2. Spick AC current with high frequency component. 10.1.1.2. Power Factor control circuit Feature: 1.
10.2. Energy Recovery Drive Pulse Output 10.2.1. Plasma Panel Energy Loss When The Sustain, Scan and Data drive pulses are supplied to the plasma panel a lot of energy was lost by resistance of the electrodes lead and many of switching elements. Because plasma panel has the stray capacitance and this capacitance makes high level inrush current during the charge and dischange.
19 Specifications Specifications Power Source: AC220 - 240V 50/60Hz (50WP16SERIES) AC120V 50/60Hz (50HP81) Power Consumption: 530 W 3.0W (stand-by condition) 1.4W (Power off condition) Plasma Display panel: Drive method AC type 50-inch, 16:9 aspect ratio Contrast Ratio 3000:1 Brightness Capability (Panel only) 500 cd / m (As a set) 300 cd / m Screen size:...