Teac PL-D2000 Service Manual

Teac PL-D2000 Service Manual

Av digital home theater system
Hide thumbs Also See for PL-D2000:

Advertisement

SERVICE MANUAL
P P L L - - D D 2 2 0 0 0 0 0 0
AV Digital Home Theater System
NOTES
PC boards shown are viewed from parts side.
The parts with no reference number or no parts number in the
exploded views are not supplied.
As regards the resistors and capacitors, refer to the circuit diagrams
contained in this manual.
Parts marked with this sign are safety critical components. They
£
£
must be replaced with identical components - refer to the appropriate
Parts List and ensure exact replacement.
Parts of [ ] mark can be used only with the version designated.
Effective : April, 2002
S-0057A

Advertisement

Table of Contents
loading

Summary of Contents for Teac PL-D2000

  • Page 1 SERVICE MANUAL P P L L - - D D 2 2 0 0 0 0 0 0 AV Digital Home Theater System NOTES PC boards shown are viewed from parts side. The parts with no reference number or no parts number in the exploded views are not supplied.
  • Page 2: Table Of Contents

    1 SAFETY INFORMATION CONTENTS This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of 1968", and is 1 SAFETY INFORMATION classified as a class 1 laser product. There is no hazardous invisible laser radiation during operation because invisible laser 2 SPECIFICATIONS radiation emitted inside of this product is completely confined in...
  • Page 3: Specifications

    2 SPECIFICATIONS DVD Player Speakers Pickup: Semiconductor laser, Wavelength 650 nm Active Subwoofer: Signal system: NTSC / PAL Power: 50 W (4ohms at 80 Hz, THD 10%) Video signal horizontal resolution: More than 480 lines (DVD) Speaker system: Bass reflex Video signal-to-noise ratio: More than 60 dB (DVD) Speaker unit: 8 inches, dia.
  • Page 5: Adjustment And Checks

    3 ADJUSTMENTS AND CHECKS ALIGNMENT INSTRUCTIONS EQUIPMENT NEEDED: AM Signal Generator FM Signal Generator Oscilloscope VTVM(AC, DC) Test loop antenna (AW Adjustment) Dummy antenna (FM Adjustment) Stereo signal modulator Frequency counter Distortion analyser IMPORTANT 1. Check power-source voltage. 2. Set the function switch to band aligned. 3.
  • Page 6 1. FM, AM TRACKING VOLTAGE ADJUSTMENTS (FM, AM) DC VOLTMETER ......CONNECT TO TEST POINT R109 and GND R109 Band Frequency Adjust for Adjustment 87.50MHz [EUR,US] 1.5V 76.00MHz [J] 108.00MHz [EUR,US] 8.4V 90.00MHz [J] 522kHz [EUR,J] 1.5V T101 530kHz [US] 1620kHz [EUR,J] 8.3V TC102...
  • Page 7 3. FM MONO DISTORTION ADJUSTMENT AC VOLT METER ......Connect to the output. Signal Generator......Connect to FM ANT Jack (FM IN) through the dummy. Distortion Meter ......Connect to the output. Frequency Adjust for Adjustment 98.10MHz [EUR,US] Minimum T.H.D FE001 82.00MHz [J] (<1%) 4.
  • Page 8: Exploded Views And Parts List

    4 EXPLODED VIEWS AND PARTS LIST EXPLODED VIEW-1...
  • Page 9 EXPLODED VIEW-1 £ £ £ £ £ £ £ £ £ £...
  • Page 10 EXPLODED VIEW-1 £ £ £ £ £ INCLUDED ACCESSORIES...
  • Page 11 EXPLODED VIEW-2...
  • Page 12 EXPLODED VIEW-2 £ £ £ £ £ £ £ £ £ £ £...
  • Page 13 EXPLODED VIEW-3...
  • Page 14 EXPLODED VIEW-3...
  • Page 15: Pc Boards And Parts List

    5 PC BOARDS AND PARTS LIST MAIN PCB (SIDE A)
  • Page 16 MAIN PCB (SIDE B)
  • Page 17 KEY PCB REGIONAL JW281 JW282 JW283 JUMPER WIRE SETUP: 1=INSTALL, 0=NOT INSTALL TUNER PCB POWER PCB...
  • Page 18 MPEG PCB (SIDE A) MPEG PCB (SIDE B)
  • Page 19 SCART PCB (SIDE A) SCART PCB (SIDE B)
  • Page 20 MAIN PCB ASSY MAIN PCB ASSY £ £ £ £ £ £ £ KEY PCB ASSY (GATHER) £ £ £ £ £ £ £ £...
  • Page 21 TUNER PCB ASSY POWER PCB ASSY £ £ £ £ MPEG PCB ASSY POWER PCB ASSY £ £ £ £...
  • Page 22 PRO LOGIC+SCART PCB ASSY AMP PCB ASSY [SUB WOOFER] £ £ £ JACK SWITCH PCB ASSY [SUB WOOFER] £ LED+SW PCB ASSY (GATHER) [SUB WOOFER] £ £ £ £ £ £ £ £ £...
  • Page 23: Block Diagram

    6 BLOCK DIAGRAM...
  • Page 24: Wiring Diagram

    7 WIRING DIAGRAM...
  • Page 25 PL-D2000 SCHEMATIC DIAGRAM...
  • Page 27 INSTRUCTIONS FOR SERVICE PERSONNEL BEFORE RETURNING APPLIANCE TO THE CUSTOMER, MAKE LEAKAGE- CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT.
  • Page 28 PL-D2000 HOME THEATER SYSTEM 1 st Issue; September 2001...
  • Page 29 PL-D2000 SCHEMATIC DIAGRAM Applicable serial number 1100XXXX-YYY...
  • Page 31 INSTRUCTIONS FOR SERVICE PERSONNEL BEFORE RETURNING APPLIANCE TO THE CUSTOMER, MAKE LEAKAGE- CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT.
  • Page 32 PL-D2000 HOME THEATER SYSTEM 1 st Issue; October 2002...

Table of Contents