SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ......................A1-1 HOW TO ORDER PARTS ..........................A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ......................... B1-1 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ..............B2-1, B2-2 SERVICE MODE LIST .............................
GENERAL SPECIFICATIONS G - 1 CRT Size / Visual Size 13 inch / 335.4mmV System CRT Type Normal Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 1Speaker Position Bottom Size 3 Inch Impedance Sound Output 1.0 W 10%(Typical) 0.8 W NTSC3.58+4.43 /PAL60Hz G - 2...
Page 5
GENERAL SPECIFICATIONS Color Stream Channel(TV/Cable) CH Label Sleep Timer Sound Mute V-chip Rating G - 8 OSD Language English French Spanish G - 9 Clock and Sleep Timer Max Time 120 Min Timer Step On/Off Timer Program(On Timer / Off Timer) Wake Up Timer Timer Back-up (at Power Off Mode) more than...
Page 6
GENERAL SPECIFICATIONS Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter Lines Auto CH Memory Hotel Lock Closed Caption Stable Sound Energy Star Power On Memory Favorite CH G - 1 2 Accessories Owner's Manual Language English / Spanish...
Page 7
GENERAL SPECIFICATIONS Gross (Approx.) 11.0kg ( 24.4lbs) G - 1 6 C arto n Master Carton Content ---- Sets Material Dimensions W x D x H(mm) x -- x -- Description of Origin Gift Box Material Double/Brown Dimensions W x D x H(mm) x 408 x 380 Design...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 10
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. Table 1 Enter DATA SET mode by setting VOLUME to minimum.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: CUT OFF Read and perform these adjustments when repairing the Adjust the unit to the following settings. circuits or replacing electrical parts or PCB assemblies. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64, B.BIAS=64, BRI.CENT=120, CONT.MAX=40. CAUTION Place the set with Aging Test for more than 15 minutes.
Page 14
ELECTRICAL ADJUSTMENTS 2-8: OSD HORIZONTAL Activate the adjustment mode display of Fig. 1-1. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) "A" Fig. 2-1 00 OSD H Fig.
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
BLOCK DIAGRAM TU001 EARHONE JACK 11 12 J1001 CH. DOWN IC1001 AN7511 VOL. DOWN SPEAKER SOUND AMP CH. UP SP1001 RGB Proc.2 VOL. UP Q801 OSD SW CONTRAST BRIGHTNESS RED OUT RGB OUTPUT Chroma Proc. Stage DRIVE Q802 ACC/C-BPF CUT OFF APC/KILLER OS101 GREEN OUT...
Page 21
TV POWER SCHEMATIC DIAGRAM (MAIN PCB) CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. ATTENTION 4A 125V :POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501). TO SOUND/AV R517 D505...
WAVEFORMS 16 50V 20 s/div SOUND/AV 0.5V 1ms/div 1V 1ms/div 200mV 500 s/div 20 500mV 20 s/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 31
CLASS 1 LASER PRODUCT MT1134 SERVICE MANUAL COLOR TELEVISION RECEIVER REVISION 1 MFR’S VERSION A MFR’S VERSION V801 A34AGT13X98(L) A34JXV70X53N45 Please file the revision with the original version.
Page 32
Change of CRT ELECTRICAL REPLACEMENT PARTS LIST MFR'S VERSION B MFR'S VERSION A PART NO. DESCRIPTION PART NO. DESCRIPTION REF. NO. ! V801 098Q1404B2 CRT W/DY A34AGT13X98(L) 098Y1404B9 CRT W/DY A34JXV70X53N45 SPEC.NO. M3R0-06X O/R NO. K4X3003...
Page 33
MT1134 SERVICE MANUAL COLOR TELEVISION RECEIVER REVISION 2 MFR’S VERSION C MFR’S VERSION V801 IC101 A34JXV70X53N45 OEC7091B A34AGT13X98(L) OEC7091C Please file the revision with the original version.
Page 34
MICON VERSION UP ELECTRICAL REPLACEMENT PARTS LIST MFR'S VERSION A MFR'S VERSION C PART NO. DESCRIPTION PART NO. DESCRIPTION REF. NO. IC101 I56F07091B IC OEC7091B I56F07091C IC OEC7091C MAIN PCB ASS'Y (VERSION A) MAIN PCB ASS'Y (VERSION C) PCB010 A3R002X010 A3R002X010 TMD604B TMD604B...