SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
Page 3
CONTENTS SERVICING NOTICES ON CHECKING ......................A1-1 HOW TO ORDER PARTS..........................A1-1 IMPORTANT..............................A1-1 CONTENTS..............................A2-1 GENERAL SPECIFICATIONS......................... A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP......................... B1-1 2. REMOVAL OF DEFLECTION YOKE..................... B2-1 3. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC..............B3-1, B3-2 SERVICE MODE LIST .............................
GENERAL SPECIFICATIONS G-1.Outline of the Product 9 inch(222.8mmV):Measured diagonally Color CRT 90 degree deflection G-2.Broadcasting System System G-3.Color System NTSC SECAM or Monochrome signal G-4.NTSC Playback(PAL 60Hz) Not Applicable G-5.NTSC 3.58+4.43/PAL60Hz Not Applicable G-6.Antenna Input Impedance VHF/UHF 75 ohm unbalanced G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System...
Page 5
GENERAL SPECIFICATIONS G-18.Regulation Safety NEMKO FEMKO DEMKO IEC65 SEMKO HOMOLO SABS SISIR AS3159 DENTORI GOST NONE Radiation SABA HOMOLO CISPR13 DENTORI AS/NZS NONE X-Radiation DHHS DENTORI NONE G-19.Temperature : Operation ºC ~ 40 ºC Storage ºC ~ 60 ºC G-20.Operating Humidity Less than G-21.Clock and Timer Sleep Timer...
Page 6
GENERAL SPECIFICATIONS G-26.OSD Language OSD Language Setting Not Applicable G-27.Speaker NONE Layout Front Side Bottom Size/Quantity inches x Imp. Power Max. 10 % W (Typical) G-28.EXT Speaker : Imp. Power Max. 10 % W (Typical) G-29.Carton Master Carton: Need No Need Content: ---- Material:...
Page 7
GENERAL SPECIFICATIONS G-32.Switch Front Power Channel Up/Reset Volume Up/Set+ System Select Channel Down/Enter Volume Down/Set- Main Power S W Sub Power Menu TV/AV Picture Rear AC/DC TV/CATV Selector Degauss Main Power S W G-33.Magnetic Field BV : +0.45G BV : +0.35G BV : +0.25G...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP INSTALLATION Clean the spot where the cap was located with a small Read the following NOTED items before starting work. amount of alcohol. (Refer to Fig. 1-3.) After turning the power off there might still be a potential voltage that is very dangerous.
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DEFLECTION YOKE (Refer to Fig. 2-1) Loosen the screw 1. Remove the Convergence • Purity Magnet in the direction of arrow (A). Remove the 3 Wedges. Remove the Deflection Yoke in the direction of arrow (A).
Page 10
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 3-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 11
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 3-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key simultaneously for more tan 1 second.
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL 1. RF AGC DELAY ADJUSTMENTS 2. VIDEO LEVEL 3. FM LEVEL Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. 4. OSD H 5. CUT OFF CAUTION 6.
Page 14
ELECTRICAL ADJUSTMENTS 2-7: SUB CONTRAST 1. BRIGHT Receive the monoscope pattern. (RF Input) 2. CONTRAST Activate the adjustment mode display of Fig. 2-1 and press 3. COLOR the channel button (4) on the remote control to select 4. TINT "PICTURE". The Fig. 2-4 appears on the display. 5.
Page 15
ELECTRICAL ADJUSTMENTS 2-11: VERTICAL SIZE Receive the monoscope pattern. Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 2-1 and press the channel button (1) on the remote control to select "H/V".
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
Page 24
POWER SCHEMATIC DIAGRAM (TV MAIN PCB) R518 DEGAUSS SW Q508 3.3K DTA114ES CP501 Q507 DC JACK CR2AM-8-F8 R520 TV-50P-02-L1 C515 J501 DEGAUSS COIL PROTECTOR HEC0824-010010 L502 250V ECQ-E Q506 RY501 8R090007 DTC114ES ALKS329 D504 R512 MTZJ16B FROM/TO MICON/TUNER 11.5 S100Y DC POWEWR SW Q509 DTA114ES...
Page 25
AV/SOUND SCHEMATIC DIAGRAM (TV MAIN PCB) C301 W802 C353 FROM MICON/TUNER R355 AUDIO_MUTE R353 47K 1/4W POWER EXT.SPEAKER/DIVERSITY J702 TC38-001-05-T W805 FROM/TO CHROMA C355 W846 AUDIO_OUT P.CON+9V TU_AUDIO_OUT SWD_AUDIO TUNER_VIDEO HS351 SWD_VIDEO 763WSA0009 VIDEO SW IC IC702 NJM2245L AUDIO SW IC IC701 NJM2234L BUFFER...
Page 26
WAVEFORMS MICON/TUNER 0.5V 10µs/div 13 200mV 20µs/div 0.5V 10µs/div 0.5V 10µs/div 14 200mV 5ms/div 1.0V 20µs/div 10 200mV 10µs/div 15 0.5V 20µs/div 1.0V 5ms/div CHROMA 20.0mV 1ms/div 11 100mV 0.1µs/div 16 0.5V 20µs/div 200mV 50µs/div 12 10.0V 20µs/div 17 0.5V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 27
WAVEFORMS DEFLECTION/CRT 18 200mV 5ms/div 23 10.0V 5ms/div 24 10.0V 20µs/div 19 20.0V 20µs/div 20 5.0V 20µs/div 25 10.0V 20µs/div 21 200V 20µs/div 26 10.0V 20µs/div 22 5.0V 5ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.