Service Manual MT1132 13” Color Television THIS SERVICE MANUAL IS FOR MT1132 SUFFIX A , B , C AND D CRT USAGE SUFFIX A SUFFIX B SUFFIX C SUFFIX D V451 5721-014ST37N 5721-37CN030T 5721-026TT37N 5721-030ZT37N (37GDA86X) (370KSB22(SYB)) (A34JFQ90X) (A34JXV70X) DY501...
FEATURES On-screen graphics guide you through setup features and operations Automatic programming of channels allows easy selection of stations available in your viewing area Sleep timer programs the TV to turn itself off at a preset time One day timer programs the TV to come on once at a preset time Weekly timer programs the TV to come on at a preset time every day 26 button infrared remote control allows remote operation VHF/UHF/CATV tuning allows reception of standard broadcasts or cable TV channels...
IMPORTANT SERVICE SAFETY INFORMATION Operation of receiver outside of cabinet or with back removed PROTECT YOUR CUSTOMER 1. Inspect all lead dress to make certain that leads are not involves a shock hazard. Work on these models should only be performed by those who are thoroughly familiar with pinched or that hardware is not lodged between the chassis and precautions necessary when working on high voltage...
( ADJUSTMENT BY REMOTE CONTROL ) ADJUSTMENT MODE The following adjustment items can be performed from menus by Remote Control as shown below : NOTE: The button combination and position on the Remote Control to select the adjustment items is given on page 4. 1.
INSTALLATION AND SERVICE INSTRUCTION CAUTION: Use an isolation transformer when performing any service on this chassis. SHUTDOWN CIRCUIT: When the high voltage rises, there are simultaneous voltage increase developed at terminal 6 of the Horizontal Output Transformer ( T671 ) and applied to pin 29 of IC301. If excessive high voltage is produced, the increased voltage developed exceeds the rating of zener diode D552 causing the Horizontal Oscillator to stop functioning and the high voltage system to shut down.
SOUND IF ADJUSTMENT Connect TV Test Pattern Generator (NTSC signal, 70dB u , channel 2) to EXT. Antenna Terminal (TE1) through TV Channel Signal Generator. (Standard modulation is 400Hz at 25kHz deviation for sound signal. 2. Connect positive lead of DC Digital Voltmeter to TP7 and negative lead to TP4. 3.
Page 9
STATIC CONVERGENCE ADJUSTMENT ( Refer to Figure 3 and 4 ) IMPORTANT: Before proceeding, make sure the location of the convergence magnet assembly on the neck of the CRT is as shown in Figure 3. The rear edge of this assembly must be positioned 65 mm from the tip of the CRT base.
FIG. 5 FOCUS ADJUSTMENT Adjust focus control, located on the Horizontal Output Transformer (T671), for maximum overall definition and fine picture detail with Brightness and Contrast controls set at normal viewing levels. BLACK AND WHITE ADJUSTMENT ( CUTOFF / WHITE BALANCE ) The purpose of this procedure is to adjust the bias applied to the color picture tube for reproducing a quality monochrome picture at all brightness levels and also to achieve maximum usable brightness.
VERTICAL PHASE ADJUSTMENT Connect TV Test pattern Generator (NTSC signal 70dB u, Monoscope Pattern) to EXT. Antenna Terminal (TE1) through TV Channel Generator. ( NOTE: For steps 2, 3 and 4 below, refer to page 3 for Adjustment By Remote Control Method). 2.
Page 12
VIDEO IN ADJUSTMENT Connect Pattern Generator (1Vp-p, Color Bar Pattern) to video jack (J701). Connect positive lead of Oscilloscope probe 1 to R703 and negative lead of Oscilloscope to TP4 to detect video in signal. Connect positive lead of Oscilloscope probe 2 to TP10 and negative lead of Oscilloscope to TP4. Select Video Mode by remote control.
TEST POINT TP 2(-) PCB 1 T671 TU 1 C609 IC301 D552 VR701 T203 TP10 TP 9 TP11 T202 PCB 2 TP 7 TP15 VR702 R453 (GND) TP8 VIDEO SU401 TP16 R452 IC101 R451 TP14 TP13 - 12 -...
Page 14
VOLTAGE CHART ( all in volts ) OPERATION CONDITION : TINT, BRIGHT and COLOR CONTROL……….. CENTER CONTRAST ………………………………………. MAXIMUM COLOR BAR SIGNAL IC101 TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt TERMINAL No Volt IC102 TERMINAL No Volt IC301 TERMINAL No...