Honeywell FocusPRO TH6110D Installation Manual
Honeywell international inc. programmable thermostat installation guide
Hide thumbs
Also See for FocusPRO TH6110D:
- Operating manual (28 pages) ,
- Manual (16 pages) ,
- Installation manual (9 pages)
Table of Contents
Table of Contents
Related Manuals for Honeywell FocusPRO TH6110D
Summary of Contents for Honeywell FocusPRO TH6110D
-
Page 1: Installation Guide
Installation Guide TH6110D Programmable Thermostat... -
Page 2: System Settings
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. Copyright © 2005 Honeywell International Inc. All rights reserved. Power Options • Battery power only •... -
Page 3: Table Of Contents
Installer system test ...9 Explanation of features ...10 Installation tips Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperature. Do not install in locations where the thermostat can be affected by: •... -
Page 4: Pre-Installation Checklist
Installation Guide Pre-installation checklist Package contents Check to make sure your package includes the following items: Quick FocusPRO ™ TH6110D Operating manual reference programmable thermostat card (wallplate attached to back) Wall anchors and AA alkaline mounting screws batteries (2) (2 each) Required tools &... -
Page 5: Wallplate Installation
FocusPRO ™ TH6110D Programmable Thermostat Wallplate installation Insert finger into wire hole and pull to remove wallplate from thermostat. Insert quick reference card Drill 3/16” holes for drywall. Drill 7/32” holes for plaster. Wall anchors Remove the wallplate from the ther- mostat as shown at left, then follow directions below for mounting. -
Page 6: Wiring
C terminal The C (common wire) terminal is optional when thermostat is powered by batteries. W (O/B) terminal If thermostat is configured for a heat pump in the Installer Setup, configure changeover valve for cool (“O” factory setting) or heat (“B”). -
Page 7: Wiring Diagrams
FocusPRO ™ TH6110D Programmable Thermostat Wiring diagrams Power supply. Provide disconnect means and overload protection as required. Factory-installed jumper. Remove for 2-transformer systems only. Optional 24VAC common connection. In Installer Setup, set system type to Heat Only. In Installer Setup, set system type to Heat Pump & changeover valve to 0 or B. - Page 8 Installation Guide Wiring diagrams Power supply. Provide disconnect means and overload protection as required. Factory-installed jumper. Remove for 2-transformer systems only. Optional 24VAC common connection. In Installer Setup, set system type to Heat Only. In Installer Setup, set system type to Heat Pump & changeover valve to 0 or B. Typical heat-only system with fan Typical cool-only system Heat-only system (Series 20)
-
Page 9: Power Options
FocusPRO ™ TH6110D Programmable Thermostat Power options & mounting Connect common side of transformer to “C” terminal Install batteries in back of thermostat (optional if AC powered). AC Power The thermostat can be powered by 24 VAC power, or by batteries. -
Page 10: Installer Setup
Installation Guide Installer setup Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired. To begin, press and hold the buttons until the display changes Setup Function System type Changeover valve... -
Page 11: Installer System Test
FocusPRO ™ TH6110D Programmable Thermostat Installer system test Follow the procedure below to test the heating, cooling and fan. To begin, press and hold the buttons until the display changes System Test Heating system Cooling system Fan system Thermostat information... -
Page 12: Adaptive Intelligent Recovery
Adaptive Intelligent Recovery Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature.The thermostat then turns on the heating or cooling at just the... -
Page 13: Quick Reference To Controls
FocusPRO ™ TH6110D Programmable Thermostat Quick reference to controls Digital display screen Function buttons Press to select the function displayed just above each button. (Functions change depending on the task.) Quick reference to display screen Current inside temperature Current program period... -
Page 14: In Case Of Difficulty
Installation Guide In case of difficulty If you have difficulty with your thermostat, please try the suggestions below. Most problems can be corrected quickly and easily. Display is blank • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. -
Page 15: Accessories/Replacement Parts
FocusPRO ™ TH6110D Programmable Thermostat In case of difficulty Heating equip- • Check Installer Setup, Function 1 (System Type), to make sure it is set to ment is running match the installed heating/cooling equipment (see page 8). in cool mode Cannot change •... - Page 16 Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 ® U.S. Registered Trademark. Patents pending. Copyright © 2005 Honeywell International Inc. All rights reserved. Printed in U.S. Document number 69-1714. Date 01-2005. Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 www.honeywell.com/yourhome...
Need help?
Do you have a question about the FocusPRO TH6110D and is the answer not in the manual?
Questions and answers
How do I set up for operation on certain days and times?
To set up the Honeywell TH6110D for operation on specific days and times:
1. Press the SET CLOCK/DAY/SCHEDULE button.
2. Use the ▲ or ▼ buttons to set the correct time.
3. Press SET CLOCK/DAY/SCHEDULE again to set the day of the week using ▲ or ▼.
4. Press DONE to save and exit.
To set program schedules:
- Default schedule assumes: wake at 6 a.m., leave at 8 a.m., return at 6 p.m., sleep at 10 p.m.
- To change these, refer to pages 9–11 of the manual. You can override the program manually at any time.
This answer is automatically generated
Cannot figure out how to turn off automatic settings -do not want temperature to change automatically at different times of day. I would like to do it manually. Thank you.
To turn off the automatic settings and control the temperature manually on the Honeywell TH6110D thermostat:
1. Enter Installer Setup.
2. Go to Function 12 (System Setting).
3. Change the setting to "Manual" or "Auto Changeover" as needed.
This disables automatic scheduling and allows manual temperature control.
This answer is automatically generated