Advertisement
Honeywell WiFi Thermostat
Integration Release Notes
Content
Introduction...1
Last modified: 05/03/18
Introduction
The Honeywell WiFi thermostats are a series of WiFi thermostats that have been
tested and certified for integration with the ClareHome system.
When integrating a Honeywell WiFi thermostat into your ClareHome project, no
extra connections are necessary. Install the thermostat according to the
Honeywell documentation, register the thermostat on the Honeywell portal,
enable auto mode in the thermostat, and then connect it to the network using IP.
All HVAC integrations share a common UI, so that the user experience is
consistent. Temperature settings can be controlled via events. Use Fusion's
Scenes and Rules to automate the actions your customers want.
Supported models:
TH9320WF
TH8320WF
TH8321WF
Doc ID - 1188 • Rev 04
RTH-8580WF
RTH9580WF
RTH6580WF
TH6320WF1005/B
1 / 8
Advertisement
Related Manuals for Honeywell TH9320WF
Summary of Contents for Honeywell TH9320WF
-
Page 1: Table Of Contents
Contact information...8 Last modified: 05/03/18 Introduction The Honeywell WiFi thermostats are a series of WiFi thermostats that have been tested and certified for integration with the ClareHome system. When integrating a Honeywell WiFi thermostat into your ClareHome project, no extra connections are necessary. Install the thermostat according to the Honeywell documentation, register the thermostat on the Honeywell portal, enable auto mode in the thermostat, and then connect it to the network using IP. -
Page 2: Installing The Honeywell Thermostat
The Following figure shows the Honeywell controls on the ClareHome UI. Figure 1: User interface of the Honeywell WiFi thermostat. (1) Change the Heat set point by sliding the indicator around the dial. (2) Change the Cool set point by sliding the indicator around the dial. -
Page 3: Registering The Thermostat
Registering the thermostat After installation, you must register the thermostat on the Honeywell portal. This allows the thermostat to be accessed remotely and updated with information from the Honeywell portal To register the Honeywell thermostat: To register your Honeywell WiFi devices, you must have each device’s Note: MAC ID and Device CRC. -
Page 4: Configuring In Fusion
1. Click the Devices tab, and then click the New Device button to display the Select Template dialog. 2. Expand the Climate folder, and browse to the Honeywell WiFi Thermostats. Climate > IP Thermostats > Honeywell WiFi Thermostats Doc ID - 1188 • Rev 04... - Page 5 1, the second thermostat is 2, and so on. • Device Name: The thermostats name in the Honeywell WiFi portal. Note: The names in the Honeywell portal and Fusion must be identical or the thermostat will not connect. The names are case sensitive.
-
Page 6: Configuring Rules With Tcc Thermostats
7. Click the Save button 8. The Create Service dialog displays. Click OK, and the service is automatically created for you. Note: You can select Open Wizard to check or change the controls points as needed. 9. Configure rules to work with your thermostat. Configuring rules with TCC thermostats Configure a rule for your thermostat. - Page 7 4. Configure the Event Part as below. • Event Type: Device Property Change Event Note: This event type is replacing the Device Property Value Event. • Device: Honeywell WiFi thermostat • Function: Heat Cool Temperature Actuator • Property: Unit • Constraint: >...
-
Page 8: Contact Information
Contact information Clare Controls, LLC. 7519 Pennsylvania Ave, Suite 104 Sarasota, FL 34243 General: 941.328.3991 Fax: 941.870.9646 www.clarecontrols.com Integrator/Dealer Support: 941.404.1072 claresupport@clarecontrols.com Homeowner Support (ClareCare): 941.315.2273 (CARE) help@clarecontrols.com Doc ID - 1188 • Rev 04 8 / 8...