Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Digitus DN-15024
Summary of Contents for Digitus DN-15024
- Page 1 POWERLINE HIGH SPEED NETWORK BRIDGE User Manual DN-15024 / DN-15025...
- Page 2 Safety This equipment has been tested and found to comply with Part 15 Class B of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment is in compliance with the requirements of the following regulations: CE Mark, 89/336/EEC RoHS This product is RoHS compliant.
-
Page 3: Table Of Contents
Table of Contents HomePlug Powerline ........................... 4 Introduction..............................4 System Diagram ............................. 4 Casing Details ..............................5 Front Casing ..............................5 Status Lights..............................5 Bottom Casing ..............................6 Buttons ................................6 Initial Setup ..............................6 Connect the HomePlug AV Ethernet Bridge to a Computer or Modem/Router ..........6 Individual HomePlug AV Network Setup (Optional) ................. -
Page 4: Homeplug Powerline
1 HomePlug Powerline HomePlug power line is an excellent solution that can be used to extend your network. In the home or small office building, use HomePlug Ethernet Bridges to link multiple locations without the need to run long Ethernet cables. Combined with a broadband DSL/Cable connection, every room with electrical power outlets will have easy access to high-speed Internet connection. -
Page 5: Casing Details
1.3 Casing Details Front Casing The front casing contains 3 status lights: Power, PLC Link, and Ethernet Link. (INSERT FINAL CASING DESIGN) Ethernet Link Light PLC Link Light Power Light Status Lights Power On: This HomePlug Ethernet Bridge is receiving electrical power Off: Power off PLC Link The PLC (Powerline) Link light will indicate the overall speed of your network with 3 colors:... -
Page 6: Bottom Casing
Bottom Casing The bottom casing contains a recessed Reset Button, a Security Button, and an Ethernet Port. (INSERT FINAL CASING DESIGN) Ethernet Port Security Button Reset Button Buttons Security This button is designed to generate an individual HomePlug AV network group under multiple nodes environment. Please refer to the optional Individual HomePlug AV Network Setup section below for more details. -
Page 7: Individual Homeplug Av Network Setup (Optional)
2 Individual HomePlug AV Network Setup (Optional) All HomePlug AV Ethernet Bridges ship with a default security key so they will automatically link to all other HomePlug AV Ethernet Bridges sharing the same electrical lines. If there are other HomePlug AV Ethernet Bridges in the building (such as in an office or apartment building), you may want to create your own individual HomePlug AV network group so other HomePlug AV Ethernet Bridges cannot connect to your network. -
Page 8: Adding Bridge C To Existing Network Ab (Network Abc)
2.2 Adding Bridge C to existing Network AB (Network ABC) One unassociated Bridge C is added to an existing Network AB. The procedure is as follows: 1. Press and hold the Security button on Bridge C for 10 seconds. Release it when the Power light flashes. The password to Bridge C has just been erased. -
Page 9: Removing Bridge B From Bridge A & C Network And Join With Bridge D & E (Network Bde)
2.3 Removing Bridge B from Bridge A & C Network and join with Bridge D & E (Network BDE) The procedure is as follows: 1. Press and hold the Security button on Bridge B for 10 seconds. Release it when the Power light flashes. The password to Bridge B has just been erased and removes itself from Bridge A &... -
Page 10: Troubleshooting
3 Troubleshooting If your HomePlug AV 500Mbps Ethernet Bridges have difficulty communicating with each other, check the following: Try power cycling the unit by unplugging it from the wall for 10 seconds and plugging it in again. Use a pin and hold the Reset button down for 2 seconds on each unit you are trying to connect. The HomePlug AV 500Mbps Ethernet Bridge’s light will flash, the units will reset and attempt to link using default factory settings. -
Page 11: Specification
4 Specification Main Chipset Atheros AR7400 Computer Interface IEEE802.3 (10BASE-T) IEEE802.3u (100BASE-T) IEEE802.3ab (1000BASE-T) Data PHY Rate Up to 500 Mbps Standards IEEE 1901 / HomePlug AV Network Interface One RJ-45 (10/100Base-T Ethernet) One 500Mbps HomePlug AV Power Line Port supporting co-existence with HomePlug 1.0 (14/85Mbps) Security 128-bit AES Link Encryption with Key Management...
Need help?
Do you have a question about the DN-15024 and is the answer not in the manual?
Questions and answers