Honeywell 3820 Quick Start Manual

Cordless imaging systems
Hide thumbs


3820, 3820i, 4820, 4820i
Cordless Imaging Systems

Quick Start Guide



  Also See for Honeywell 3820

  Related Manuals for Honeywell 3820

  Summary of Contents for Honeywell 3820

  • Page 1: Quick Start Guide

    3820, 3820i, 4820, 4820i Cordless Imaging Systems Quick Start Guide...
  • Page 2: Getting Started

    Note: Refer to your user’s guide for information about cleaning your device. For localized language versions of this document, go to Getting Started Turn off the computer’s power before connecting the base, then power up the computer once the base is fully connected.
  • Page 3 Keyboard Wedge Connection Serial (RS-232) Connection...
  • Page 4: Reading Techniques

    Reading Techniques The view finder projects an aiming beam that should be centered over the barcode. (The 4820/4820i can be positioned in any direction for a good read.) Hold the imager over the barcode, pull the trigger, and center the aiming beam on the barcode. The aiming beam is smaller when the imager is closer to the code and larger when it is farther from the code.
  • Page 5: Standard Product Defaults

    Standard Product Defaults This barcode resets all standard product default settings. Standard Product Defaults PC Interface Scan the barcode that describes the PC or interface you are using. USB Keyboard (PC) Japan DOS/V RS-232 USB Japanese Keyboard (PC)
  • Page 6: Keyboard Country

    PC Interface (continued) AT/PS2 Keyboard Wedge Keyboard Country Scan the Program Keyboard Country barcode below, then scan the numeric barcode(s) from page 12, then the Save barcode to program the keyboard for your country. As a general rule, the following characters are not supported by the imager for countries other than the United States: @ | $ # { } [ ] = / ‘...
  • Page 7 Great Britain Note: For complete list of country codes, see the User’s Guide for your product at our website, Open Link Scan the Open Link barcode, then place the imager into the base to establish a link. Placing a different imager into the base establishes a new link and the old imager is unlinked.
  • Page 8: Override Locked Imager

    Override Locked Imager If you need to replace a broken or lost imager that is linked to a base, scan the Override Locked Imager barcode with a new imager, and place that imager in the base. The locked link will be overridden;...
  • Page 9: Trigger

    Trigger The following barcodes will allow you to use the reader in Manual Trigger mode (need to press the trigger to read) or Presentation mode (the reader is activated when it “sees” a barcode). Manual Trigger (Default) Streaming Presentation™ (4820/4820i) Note: Streaming presentation mode applies only to units with advanced illumination.
  • Page 10: Reread Delay

    Reread Delay This sets the time period before the imager can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Medium Reread Delay Suffix If you want a carriage return after the barcode, scan the Add CR Suffix barcode.
  • Page 11: Add Code Id Prefix To All Symbologies

    Add Code ID Prefix to all Symbologies Note: For complete list of Code IDs, see the User’s Guide for your product at our website, Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the imager transmits the function code to the terminal.
  • Page 12: Data Format Editor Instructions

    Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Format 3.
  • Page 13: Programming Chart

    Programming Chart...
  • Page 14 Save...
  • Page 15: Visual Xpress

    North America/Canada Telephone: (800) 782-4263 (8 a.m. to 6 p.m. EST) Fax number: (315) 554-6705 E-mail: Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 E-mail: Brazil...
  • Page 16: Online Technical Assistance

    Product Service and Repair Honeywell provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before...
  • Page 17 North America Telephone: (800) 782-4263 Fax: (803) 835-8012 E-mail: Latin America Telephone: (803) 835-8000 Telephone: (800) 782-4263 Fax: (239) 263-9689 E-mail: Brazil Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105 E-mail: Mexico Telephone: +52 (55) 5203-2100 Fax: +52 (55) 5531-3672 E-mail:
  • Page 18: Online Product Service And Repair Assistance

    (B) excessive voltage or current supplied to or drawn from the interface connections, (C) static electricity or electro- static discharge, (D) operation under conditions beyond the specified operating parameters, or (E) repair or service of the product by anyone other than Honeywell or its authorized representatives.
  • Page 19 This warranty shall extend from the time of shipment for the duration published by Honeywell for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to Honeywell factory or authorized service center for inspection.
  • Page 20 These warranties are non-transferable. The duration of the limited warranty for the 2020-5B, the 4820, 4820i, 3820, and 3820i is three (3) years. The duration of the limited warranty for the imager battery is one (1) year.
  • Page 21 The information in this publication does not represent a commitment on the part of Honeywell. Honeywell shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
  • Page 22 Honeywell 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 Crdlss-02-QS Rev E 10/08...

This manual is also suitable for: