Klipsch Image One Bluetooth Owner's Manual
  1. Manuals
  2. Brands
  3. Klipsch Manuals
  4. Headphone
  5. Image ONE
  6. Owner's manual

Klipsch Image One Bluetooth Owner's Manual

Headsets
Hide thumbs Also See for Image One Bluetooth:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Image
ONe
™
BlueTOOTh
®
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Klipsch Image One Bluetooth

Summary of Contents for Klipsch Image One Bluetooth

  • Page 1 Image ™ BlueTOOTh ® Owner’s Manual...

  • Page 2: Important Safety Information

    ImpOrTaNT SafeTy INfOrmaTION reaD these instructions. 2) KeeP these instructions. 3) HeeD all warnings. 4) FOllOw all instructions. 5) DO nOT use this apparatus near water. 6) Clean OnlY with dry cloth. 7) DO nOT block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) DO nOT install near any heat sources such as radiators, heat registers, stoves, or other appara- tus (including amplifiers) that produce heat.
  • Page 3 WarNINg: except in case of emergency, Klipsch recommends you do not use these headphones or headsets (headphones plus microphone) as aviation communication equipment as they are not engineered for many environmental conditions common in commercial or non-commercial aircraft (including, but not limited to: altitude, temperature, noise conditions, unpressurized aircraft, ect) resulting in possible interference to critical communications WarNINg: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.

  • Page 4: Eu Compliance Information

    pleaSe lISTeN reSpONSIBly The Occupational safety Health administration (OsHa) has issued headphone usage recom- mendations for maximum daily exposure and sound pressure levels (measured in decibels (dB)). a decibel is a unit of measure of sound, and decibels increase exponentially as sound gets louder.
  • Page 5 fCC aNd CaNada emC COmplIaNCe INfOrmaTION This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation.
  • Page 6 Weee NOTICe note: This mark applies only to countries within the european union (eu) and norway. This appliance is labeled in accordance with european Directive 2002/96/ eC concerning waste electrical and electronic equipment (weee). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

  • Page 7: Specifications

    SpeCIfICaTIONS Bluetooth v2.1 +eDr Profiles: a2DP v1.2, aVrCP v1.0, HsP v1.2, HFP v1.6 a2DP Codecs: sBC, aaC, aptX® range: up to 10m (33 feet) Input rating: 5V DC, 0.5a STaTuS INdICaTOr example: B Blinks Blue Blinks red Time Between Blinks...

  • Page 8: What's Inside

    WhaT’S INSIde Image ONe Bluetooth headset direct Connect audio Cable Travel Case micro uSB Charging Cable...
  • Page 9 Charging Jack Volume + 2. Battery Status Indicator 8. Volume - 3. Track Back 9. audio Jack 4. Status Indicator 10. microphone 5. power/pairing 11. Track forward 6. play/pause, answer/end Call...
  • Page 10 CHARGING Charge for 1 hour before first use. when fully charged the battery will provide up to 10 hours of talking and/ or music time. You can continue to use the headset while charging. low battery (Battery status Indicator):...

  • Page 11: Turning On/Off

    3. Turn on Bluetooth on the device and set it to search for Bluetooth devices. 4. select “Klipsch BT ImageOne” from the device list. 5. If prompted to enter a passcode enter 0000. Once a device has been paired the headset will remember it. when the headset is turned on it will automatically scan for remembered devices, beginning with the most recently paired.

  • Page 12: Disconnect The Headset

    VOlume & musIC CONTROls Previous Track next Track Volume up Play / Pause Volume Down CAlls Make calls as normal from the phone, when the headset is connected the audio will automatically go to the headset. Power/Pairing Play/Pause, answer/end Call •...

  • Page 13: Reconnect The Headset

    To connect to the most recently used device, power the headset on. If Bluetooth is enabled on the device they will automatically reconnect. To connect to another remembered device, select “Klipsch BT Image One” from the Bluetooth menu of the device.
  • Page 14 sTATus INDICATOR B Blinks Blue Blinks red Time Between Blinks General and standby pairing low Battery Standby (Bluetooth Connected) Standby (Bluetooth not Connected) A2DP (streaming Audio) a2dp active, SBC codec a2dp active, aaC codec a2dp active, aptx codec HsP (Phone Calls) Incoming / Outgoing call active Call...
  • Page 15 The Bluetooth® word mark and logos are owned by the Bluetooth sIG, Inc. and any use of such marks by Klipsch Group, Inc. is under license. Other trademarks and trade names are those of their respective owners. The “aptX® software is copyright Csr plc or its group companies. all rights reserved.
  • Page 16 3502 WoodvieW Trace, indianapolis, in, Usa klipsch.com ©2012, Klipsch Group, Inc.

Table of Contents