POSIFLEX KB-4000 User Manual
POSIFLEX KB-4000 User Manual

POSIFLEX KB-4000 User Manual

Multifunction security device
Hide thumbs Also See for KB-4000:

Advertisement

Quick Links

KB-4000 / KP-100 / SD-100
MULTIFUNCTION
SECURITY DEVICE
USER'S MANUAL
Rev.: C2
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 19010900060

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KB-4000 and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX KB-4000

  • Page 1 About This Manual: Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from the furnishing, performance, or use of this material.
  • Page 2: General Description

    Ex. For KP-100, KP-110 or KB-4000 with only keypad, there will be no USB interface installed; For SD- 100 without the iButton reader, there will be no 9 pin D connector.
  • Page 3: Unpacking Contents

    MECHANICAL FIXATION For KB-4000 the stand alone security device, there is little concern about the mechanical fixation as long as the security device (keyboard) is placed in a horizontal flat surface not subject to extreme environmental conditions.
  • Page 4: Cable Connection

    PS2 cable. Connect the USB connector of KB-4000, KP-110, KP-110U or SD- 110 to a USB hub or the USB port in a PC or a Posiflex POS system. Connect the USB connector of KP-100, KP-100U or SD-100 to one of the USB ports of Jiva TP/LT series in connector area.
  • Page 5 In the cavity found at rear side of KB-4000 or KP-100 / KP-110, there is a PS/2 KB jack. Connect a standard PS/2 keyboard device to this jack and insert the cable from the PS/2 keyboard device into the cable hold groove for strain relief and fixation when a PS/2 KB is required.
  • Page 6: Keypad Programming

    In the Posiflex Product Information CD attached with Posiflex POS terminal, there is a subfolder named as “\Drivers\KP” or “\Drivers\KP100” or please download the keypad programming utility for KB-4000 / KP-100 / KP- 100U / KP-110/ KP-110U from our web site: http://www.posiflex.com.tw/DriversDownload.asp.
  • Page 7 If a PS/2 interface keyboard is to be used, please connect it to the extended PS/2 KB jack in the recessed cavity on back of KB-4000 / KP- 100/ KP-110 as mentioned earlier. Please note that there must not be any other PS/2 device connected in between the KB-4000 / KP-100 / KP-110 and the PS/2 KB port of the host system in the keypad programming operation.
  • Page 8 Please find the subfolder “\Drivers\KP\KBMSR” in the Posiflex Product Information CD or download from our web as mentioned earlier for the ISO MSR option in KB-4000 / KP-100 and go to either the subfolder “DOS” for the MSR manager under MS-DOS or the other subfolder “MSR_xxx” for setting up the MSR manager under Windows OS.
  • Page 9: Magnetic Stripe Reader

    The magnetic stripe reader in KP-100 / KP-110, KB-4000 or SD-100 / SD-110 of PS2 interface connects to the host through KB port and therefore requires no driver installation to get it working.
  • Page 10 Numerical Keypad The numerical keypad is durably pre-marked. The numerical keypad is not applicable in combination keys. DOS Application Notice for KP-100U / KP-110U The keypad KP-100U/ KP-110U connects to the host through USB port working as a USB KB and therefore also requires no driver installation except setting up the USB keyboard to be enabled in system BIOS CMOS setup.

This manual is also suitable for:

Kp-100Sd-100

Table of Contents