Honda PKH3 Installation Instructions

Firmware: PKH3 - Installation Instructions
Honda/Acura Transponder Interface: TYPE-C (7 Wire Connector)
Platform #05 firmware:- *PKT2, PKH1, PKH2, PKH3, PKH4, PKN2, PKM2, PKHY1,
PKG3, PKG8
OR
Programming
LED
Programming button
Brown Ground output when running (-) (remote start installations only)
Green N/C
Blue Ignition Input from ECM (See Vehicle Wire List for Pin # and Wire Color)
Violet/White N/C
Violet
Data
Pink/White Ignition Out (See Vehicle Wire List for Pin # and Wire Color)
Pink Ignition Input from ECM (See Vehicle Wire List for Pin # and Wire Color)
Orange
N/C
Red (+)12 VOLT CONSTANT
Black
CHASSIS GROUND
This connector has dual functions: 1) XKLOADER Firmware Upgrades. 2) 4 Pin Data 2 Data connector to remote system, which replaces
wire to wire (w2w) connection on the 10 Pin Harness.
Data (Code)
VEHICLE
Acura EL 1.7
Red/Blue
2005 - 01
Pos.:#2
Red
Acura MDX
2005 - 03 Pos.:#2
Acura RSX
Red/Blue
2005 - 02
Pos.:#2
Acura TSX
Red/Blue
2005 - 03
Pos.:#2
Acura TL Red/Blue
2005 - 04
Pos.:#2
Red/Blue
Honda Accord
Pos.:#2
2005 - 03
Honda Civic
Red/Blue
2005 - 01
Pos.:#2
Honda CRV White
2005 - 03
Pos.:#2
Honda Element
White
2005 - 03
Pos.:#2
Honda Pilot Red/Green
2005 Pos.:#2
Honda Odyssey Red/Blue
2005 Pos.:#2
Honda Ridgeline
Red/Blue
2006
Pos.:#2
Downloadable @ www.XpressDownload.com
Upgrade (Optional)
1
Data 2 Data (Optional)
2
Brown (-)
Ground output when running (-) (remote start installations only)
/
N C
Green
Blue Ignition Input from ECM (See Vehicle Wire List for Pin # and Wire Color)
N C /
Violet/White
Data (See Vehicle Wire List for Pin # and Wire Color)
Violet
Ignition Out (See Vehicle Wire List for Pin # and Wire Color)
Pink/White
Ignition Input from ECM (See Vehicle Wire List for Pin # and Wire Color)
Pink
/
N C
Orange
(+)12 VOLT CONSTANT
Red
CHASSIS GROUND
Black
WIRE FUNCTIONS
Ignition Ground (Gnd)
Black/Yellow Brown/ Yellow
Pos.:#6 Pos.:#1
Brown/ Yellow
Green/White
Pos.:#1
Pos.:#6
Brown/ Yellow
Black/Yellow
Pos.:#6 Pos.:#1
Brown/ Yellow
Black/Yellow
Pos.:#6 Pos.:#1
Black/Blue Brown/ Yellow
Pos.:#6 Pos.:#1
Black/Yellow
Brown/ Yellow
Pos.:#6
Pos.:#1
Black/Yellow Brown/ Yellow
Pos.:#6 Pos.:#1
Black/Yellow Brown/ Yellow
Pos.:#6 Pos.:#1
Black/Yellow Brown/ Yellow
Pos.:#6 Pos.:#1
Red/White Brown/ Yellow
Pos.:#6 Pos.:#1
Black/Yellow Black
Pos.:#6 Pos.:#1
Brown/ Yellow
Black/Green
Pos.:#1
Pos.:#6
Check for firmware updates before installing
Programming
Interface
1 2 3 4 5 6 7
Front view of connector

Module Programming

1. Press and hold programming button.
2. Turn the ignition key to the "ON" position, the LED will blink.
3. Release programming button.
4.Turn ignition key to the "OFF" position.
Reset
Press and hold programming button and plug module into 10 pin
harness, LED comes ON. When LED goes OFF, release
program button.
*Default Firmware
P . C .
USB
TO ECM