Advertisement
BENEFITS
Helps provide relief from allergy, asthma and respiratory
illness.
Helps clear a smokey environment quickly, so everyone
can work and relax together.
Helps reduce the time and money spent cleaning and
redecorating.
Prevents damaging black dust from
staining walls, upholstery and window coverings.
Helps reduce tobacco, cooking and pet odors.
Revitalizes the air with healthy negative ions.
Improves indoor air quality for a fresher, more
comfortable environment, year-round.
1 Dirty Air
2 Prefilter
3 Ionizing
Section
HOW IT WORKS
Dirty air is drawn in through the front grill and passes through
a 4-stage filtering system.
The Prefilter consists of foam mesh, and prevents larger
particles from entering the collecting cell.
The next step is a 2-Stage Electrostatic Collecting Cell. Dirt
particles are charged with a high negative voltage by a series
of fine ionizing wires.
through to the collecting plates where the dirt adheres to the
grounded plates, and remains until the cell is taken out and
washed.
Removes
particles
(1/2,540,000 of an inch).
The air is then drawn through an Activated Carbon Filter to
remove odors. Clean air is then discharged out the top of the
Air Cleaner.
Dual Negative Ionizer is located in the clean air stream.
Adding healthy negative ions to the air revitalizes the air
similar to that near a waterfall, spring, the ocean, or after a
rainfall.
Studies have shown that negative ions have a
beneficial effect on human biochemistry, both physically and
mentally.
OPERATING INSTRUCTIONS
1.
Remove the Air Cleaner from the box and check for
apparent damage. If your unit has any signs of damage,
immediately contact the store where the Air Cleaner was
purchased.
2.
Keep the shipping carton in case the need arises to
store or transport the unit.
3.
Remove all packaging from the unit. Choose a suitable
table or stand to allow unobstructed circulation from
front and top of unit. The unit performs best when the
back is against a wall. This enhances air circulation. To
mount unit on wall, refer to the Wall Mount Instructions.
4.
Operate Air Cleaner at voltage shown on back of unit.
4 Collecting Cell
Plates
5 Odor & Gas
Removal Filter
7 Negative Ions
and Clean Air
6 Ionizing Needle
The charged particles are drawn
down
to
0.01
5.
The System Switch controls the power to the Fan
Control Switch and the power board. When the System
Switch is ON, the red light will be illuminated.
6.
The Fan Control Switch in the front position is low
speed, the center position is medium, and the rear
position is high speed.
Use the low or medium speed for quiet, continuous or nighttime
use. Use the high speed for initial cleaning of heavy concentrations
of dirty air (i.e. smoke) or after leaving the room.
7.
The Negative Ion Emitter is activated when the fan is
ON.
You may notice arcing or snapping from the cell. It is normal to
hear some arcing when the unit is new or first turned on. It is
recommended that the Air Cleaner be run for 48 hours, when first
turned on. Arcing in the cell may also be caused by high humidity
(over 80%), after washing, or when a large particle of dirt or hair is
caught in cell. If the arcing is continuous and constant, then refer to
the Troubleshooting Chart.
micron
1.
To mount Air Cleaner on wall, remove the rear feet (2)
from the bottom of the Air Cleaner to expose the keyhole
slots.
2.
To remove the feet from the Air Cleaner, you will need a
small flat screwdriver. Pry up the center pin of the rear
foot until the head protrudes above the foot. Place the
flat portion of the screwdriver under the foot and pry up.
This will release the foot from the cabinet. Keep the feet
in case you wish to table mount the unit in future.
3.
Find the location on the wall where you wish to place the
Air Cleaner. The unit should be placed 3 ft (1 m) below
the ceiling. Use appropriate fasteners for the type of wall
the unit will be mounted and insure the head of the
screw will fit into the larger opening of the keyhole slot.
The screw head should be larger than the smaller
opening of the keyhole. The Air Cleaner weighs
approximately 13 lbs (5.9 kg). The distance between the
holes in the cabinet bottom is 14½ in (37 cm).
4.
After placing the screws in the wall, adjust the amount of
the screw sticking out to approximately 1/8 in (.32 cm).
Place the Air Cleaner over the screw head and allow the
head to slip into the keyhole slot. Pull the unit down
slightly to allow the screw head to slide into the smaller
portion of the slot.
1 - System Switch
2 - 3-Speed Fan Control Switch
3 - Negative Ion Emitter
4 - Lid which activates Safety Interlock
5 - Performance Indicator Light
WALL MOUNT INSTRUCTIONS
4
3
2
1
5
Advertisement
