Page 1
COLOR VIDEO CAMERA DXC-190 SERVICE MANUAL 1st Edition...
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. DXC-190...
Manual Structure Purpose of this manual This manual is the Service Manual of the color video camera DXC-190. This manual contains the operating instructions, service overview, operational description, electrical alignment, spare parts, semiconductor pin assignments, block diagrams, schematic diagrams and board layouts.
3-205-662-11 (1) Owner’s Record The model and serial numbers are located on the top. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. Serial No.
Page 10
When switched on, this function adjusts exposure to compensate for situations where the subject is lit from behind. Power supply The DXC-190 must always be operated with a DC 12 V power supply * or 6 SHUTTER ON/OFF switch the CMA-D2 camera adaptor (not supplied), the YS-W170/W270 camera Turning the switch on enables the 8-level electronic shutter and the CCD adaptor (not supplied).
Page 11
SH UT TE OF F 1 — A PH AS E 1 — B LO CK WH T BA SH AR P SC PH AS NO RM – – IR IS – AU TO LE NS VID EO qf qd DXC-190...
Page 12
Using an external synchronization signal 1 DXC-190 (rear) 7 Synchronization signal (e.g., switcher) Detach the old plug from the lens cable. 2 VIDEO OUT connector 8 Power supply Solder the lens cable to the pins of the supplied plug.
Page 13
Shock resistance 70 G Mass 600 g (1 lb 5 oz) Dimensions 137 (w/h/d) mm inches) Supplied accessories 4-pin plug for auto-iris lens (1) Lens mount cap (1) Operating Instructions (1) Design and specifications are subject to change without notice. DXC-190...
11. After completion of compensation, turn on the camera REVIEW FOCUS POWER and confirm that the desired points are compensated. If AUTO / MANU not, repeat steps 1 through 11. EDIT SERCH COUNTER DATA RESET SCREEN FRAME SLOW PAUSE PLAY RM-95 STOP DXC-190...
(VBS or VS). If a burst signal is detected. It The selector (IC 802) switches the superposed sync. signal is entered to the IC212-61 pin. The output of and VBS/VS signal. phase comparison with internal subcarrier DXC-190...
(SW401), and tactile switch (SW402) are arranged. 3-5. IR-29 Board A noise filter and auto iris lens connector are arranged on this board. 3-6. CT-194 Board Input/output pins, control switches, and variable resistors for adjustment are arranged on this board. DXC-190...
. For the extension between FC board and PR board ND25 (25 %) 50 by 50 mm square . Make the transmission factor to 6.25 % with double ND filter. . Oscilloscope . Frequency Counter . Digital Voltmeter . Vectorscope . Waveform Monitor . Color Monitor DXC-190...
AUTO/MAN EDIT SEARCH termination COUNTER STEP REVERSE RESET DISPLAY FRAME SLOW button DATA write button PAUSE DISPLAY MODE MODE UP button DISPLAY DISPLAY CHANGE MODE DOWN button RM-95 button DATA UP STOP CHANGE button DATA button DATA DOWN button DXC-190...
Write in initial data (Refer to 4-4-2) Has the PRE ADJUSTMENT be performed? – Board for Interface Tool – Perform the PRE ADJUSTMENT TP201 CT201 CT202 Perform the CAMERA ADJUTMENT TP203 TP202 CT203 End of Adjustment – PR-229 Board – DXC-190...
CHANGE DATA button to display Data “01”. (4) Press the DATA write button of the commander. Subject Unnecessary (5) The numerals indicated on the LCD of the commander will go out for a few seconds and then will reappear. Measurement point Nothing DXC-190...
Center 3 Press the data change button to ensure the measured voltage is within the specified value range. Subject All white pattern Measurement point Interface Tool TP2 (A/D-IN) Equipment Oscilloscope (AC 200 mV, 10 us) Display Mode Specification A/D-IN DXC-190...
Subject All white pattern indication is "50". Measurement point VIDEO OUT image level The white bright spot Waveform Monitor Equipment moves in this direction when the mode Display Mode indication is "51". Specification 65 3 IRE Image Level DXC-190...
(a) Moving direction of the bright spot when mode is “03” (b) Moving direction of the bright spot when mode is “04” (c) Moving direction of the bright spot when mode is “05” (d) Moving direction of the bright spot when mode is “06” DXC-190...
2 Shoot the all-white pattern and adjust the lens iris so that the CCD LEVEL is the specified value. Subject All white pattern PR Board CN201 1 pin (CCD LEVEL) Measurement point Equipment Oscilloscope (AC 50 mV, 10 us) Specification 250 20 mV DXC-190...
Specifica- tion Within a radius of 15 % of the vector- Conver- scope’s diameter of the origin gence spot (Suppose the vectorscope’s diameter is 100 %.) 5 Remove the C14 filter and perform step 3 and step 4. DXC-190...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
1-766-287-11 s WIRE, FLEXIBLE CARD 4-393-836-01 o BRACKET (COL), FILTER 1-769-275-11 s WIRE, FLEXIBLE CARD 7-627-551-28 s SCREW, PRECISION +P 1.4X2.5 7-627-853-88 s PRECISION SCREW +P 2X8 TYPE 3 8-729-306-92 s TRANSISTOR 2SD669A-C 7-621-772-10 s SCREW +B 2X4 7-621-772-30 s SCREW +B 2X6 DXC-190...
1-216-839-11 s METAL, CHIP 33K 5% 1/16W R426 1-216-839-11 s METAL, CHIP 33K 5% 1/16W R427 1-216-839-11 s METAL, CHIP 33K 5% 1/16W R428 1-216-839-11 s METAL, CHIP 33K 5% 1/16W RV401 1-237-038-11 s RES, ADJ, METAL 50K RV402 1-237-038-11 s RES, ADJ, METAL 50K DXC-190...
Page 32
C257 1-162-908-11 s CERAMIC, CHIP 3PF 0.25PF 50V C258 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V C259 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V C260 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V C261 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V DXC-190...
Page 33
1-162-964-11 s CERAMIC, CHIP 0.001uF 10% 50V C319 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V C385 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V C320 1-162-919-11 s CERAMIC, CHIP 22PF 5% 50V C386 1-104-851-11 s TANTALUM, CHIP 10uF 20% 10V DXC-190...
Page 34
8-759-058-54 s IC TC7S00FU(TE85R) Q209 8-729-230-60 s TRANSISTOR 2SA1586YG IC219 8-759-443-02 s IC TC75W51FU-TE12R Q210 8-729-117-73 s TRANSISTOR 2SC4178-F14 IC220 8-759-523-02 s IC TC74HC4053AFT(EL) Q211 8-729-117-73 s TRANSISTOR 2SC4178-F14 IC221 8-759-058-54 s IC TC7S00FU(TE85R) Q212 8-729-230-63 s TRANSISTOR 2SC4116YG DXC-190...
Page 35
1-216-822-11 s METAL, CHIP 1.2K 5% 1/16W R245 1-216-813-11 s METAL, CHIP 220 5% 1/16W R313 1-218-847-11 s RES, CHIP 1K 0.5% 1/16W R246 1-216-817-11 s METAL, CHIP 470 5% 1/16W R315 1-216-833-11 s METAL, CHIP 10K 5% 1/16W DXC-190...
Page 36
1-216-833-11 s METAL, CHIP 10K 5% 1/16W R377 1-216-833-11 s METAL, CHIP 10K 5% 1/16W R380 1-216-833-11 s METAL, CHIP 10K 5% 1/16W R381 1-216-864-11 s METAL, CHIP 0 5% 1/16W R382 1-216-833-11 s METAL, CHIP 10K 5% 1/16W DXC-190...
Page 37
1-424-653-11 s COIL, CHOKE 10uH R836 1-216-069-00 s METAL, CHIP 6.8K 5% 1/10W L803 1-412-030-11 s INDUCTOR CHIP 22uH R837 1-216-065-91 s RES, CHIP 4.7K 5% 1/10W L804 1-411-227-21 s INDUCTOR 100uH R838 1-216-057-00 s METAL, CHIP 2.2K 5% 1/10W DXC-190...
Page 38
R855 1-208-830-11 s RES, CHIP 100K 0.5% 1/10W ---------------------------------------- PACKING MATERIALS & SUPPLIED ACCESSORIES T801 1-450-976-11 s TRANSFORMER, CONVERTER ---------------------------------------- Ref. No. or Q'ty Part No. SP Description 1-580-173-11 s CONNECTOR, MICRO (PLUG) 4P 3-205-662-11 s OPERATING INSTRUCTION 5-10 DXC-190...
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
Page 50
PR-229 (2/2) PR-229 (2/2) . Waveforms are taken with a oscilloscope. . Circled numbers refer to waveforms. . Waveforms are measured in condition below. CAMERA color bar chart DXC-190...