Table of Contents
Advertisement
Names and functions of each part (continued)
Remote control transmitter
VIDEO,
RGB button _
_
LASER
button
Press to switch the input. (Refer to page 13, 19.)
VEOEO
Turns the laser beam on and off. Refer to page
11 cocnerning usage and observe the cautions.
STANDBY
/ ON button
_
sTAN_B¥/oN_
PosmoN
$ POSITION
button
_
Pressingthe top, bottom,leftor rightof DiskPadafter
Used to turn the power on and off.
Press for 1 sec. or more to turn the power off
(enter standby status).
(Refer to pages13 and 14.)
$ DISK
PAD
(1) Used to select menu items when the menu
screen is displayed
(refer to page 16 - 18).
(2) When the menu is not displayed,
the mouse
shift function and left click function are active.
*! (3)After
the
POSITION
button
has
been
pressed,
the screen can be moved upward,
downward and
ght.
pressing this button causes corresponding movement
(Effective only during RGB signal selection).
_¢
RESET
MOUSE
/ RIGHT
button
(1)Operates as the RESET batten when the menu
is displayed.
Press this button to return to the
initial settings,
(2)Used to click the right mouse button when the
menu is not displayed (refer to page 25,26).
*! (3)Pressing this button after scrolling the screen
with POSITION returns the screen to the original
* MENU
button
Used to turn the menu screen display on and off.
(refer to page 17 - 21).
¢ MAGNIFY
button
Used to magnify the displayed =mage.
* P in P button *2
Used to turnP in P (Picture In Picture: displays sub video
signal images in the RG8 signal) on and off.
Each time this button is pressed, operation will change in
the following sequence:
(1)
(1)- (3)
t
BLANK
button
Used to turn blanking on and off.
(Refer to page 20.)
FOCUS
button
Used to adjust the focus of the image on the
screen. (Refer to page 13.)
button
Usedto turn the freeze(still)imagedisplayon andoff.
VOLUME
button
Adjusts the volume of the sound. Press [/\]
to
increase the volume and (_/) to decrease the volume.
When there is no video signal input, operation is not
possible when the input video signal is outside the
sync range,
button
Applies Mute. (Press the Play button again to
canceL)
TIMER
button
Turns the display of the time set with the Timer
on the Menu screen on and off.
The timer is not displayed
when no input signal
is detected
or when SYNC
is out of range or
during blanking or during freezing.
Refer to page 20, 21 concerning
the method
used to set the timer.
ZOOM
button
Used to adjust the size of the image. (Refer to
page 13.)
* AUTO
button
Used to execute auto-adjust.*3
•These
functions
do not operate when initial screen message "NO INPUT
IS DETECTED"
or "SYNC
IS OUT OF RANGE" is displayed.
*1 POSITION
icon
When the POSITION
button is pressed, the moving display icon
wii[ appear at the bottom right of the screen.
While displaying the icon, you can operate POSITION.
*3 Auto adjustment
function
The projector automatically
adjusts 4 items (V. POSIT, H. POSIT,
H. PHASE, H. SIZE).
When you choose AUTO (move the cursor to the right from the
manual operation
position),
the AUTO confirmation
menu shown
below is indicated.
*2
With the P in P function,
signals
are input to both RGB and
VIDEO.
This function
operates
only when the RGB signal has
been selected. There is no display in the case of the no signal and
when the RGB signal is outside the sync range.
When P in P is used, audio is automatically switched to video.
in P in P, audio input can be switched by pressing the VOL /\and
VOL _/keys
of the remote control, displaying
the audio bar and
moving Disk Pad left and right during the display.
E_ _
RGB/VIDEO
10
• Auto adjust requires several tens of seconds.
• Auto adjust may not operate correctly in some cases
depending on the computer connected and the signal.
• Auto adjust may not operate correctly
in some case:
depending on the type of image.
• Execute auto adjust with the display of the applicafior
being run by the computer at maximum.
• After auto adjust, the image may be slightly dark in
some cases due to automatic
adjustment
of the signal
level.
• Auto adjust canot execute when the initial display is
"NO INPUT IS DETECTED"
or "SYNC IS OUT OF
RANGE" during FREEZE or MAGNIFY.
Advertisement
Table of Contents
