1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Projector
  5. CP-X885 Series
  6. User manual

Hitachi CP-X885 User Manual

Hitachi user's manual lcd projector cp-x880, cp-x885
Hide thumbs Also See for CP-X885:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Technical Manual
LCD Projector CP-X880/CP-X885
USER'S MANUAL
USER'S MANUAL
Thank you for purchasing this projector.
WARNING • Please read the accompanying manual "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
NOTE
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
MULTIFUNCTIONAL SETTINGS ........................................................................2
SPECIFICATIONS .............................................................................................11
WARRANTY AND AFTER-SERVICE................................................................12
.......................................................................................
For "TECHNICAL" see the end of this manual.
Vol.2 (Extended)
Page
1

Advertisement

Table of Contents
loading

Related Manuals for Hitachi CP-X885

Summary of Contents for Hitachi CP-X885

  • Page 1 LCD Projector CP-X880/CP-X885 USER'S MANUAL USER'S MANUAL Thank you for purchasing this projector. WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference.

  • Page 2: Multifunctional Settings

    MULTIFUNCTIONAL SETTINGS This device has 8 separate menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION, WIRELESS. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. Menu screen display : Press the MENU button. Menu selection : Use the lever switch Item selection...
  • Page 3 PICTURE-1 Menu With the PICTURE-1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table. PICTURE-1 Menu Item COLOR BAL R Adjust Red Color Balance: Dark COLOR BAL B Adjust Blue Color Balance: Dark SHARPNESS Adjust Sharpness (for VIDEO/S-VIDEO): Clear...

  • Page 4: Input Menu

    MULTIFUNCTIONAL SETTINGS (continued) INPUT Menu The three Input menu items listed in the table below can be manipulated. For RGB input, the reception signal’s horizontal and vertical frequency is displayed on the initial menu screen. Use the table below as a guide for operation. INPUT Menu Item BNC Pin (R/C...

  • Page 5: Auto Menu

    You can automatically correct vertical keystone distortion corresponding to the angle (forward/backward tilt) at which the unit is set up. • If the projection screen is inclined, or if the projector is angled downwards, it may not be possible to make the correct adjustment when V: INVERT or H&V: KEYSTONE INVERT is selected under the MIRROR item of the MAIN menu.
  • Page 6 MULTIFUNCTIONAL SETTINGS (continued) SCREEN Menu With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table. SCREEN Menu Item Selection of BLANK Screen: MyScreen The BLANK Screen may be voluntarily selected.

  • Page 7: Wireless Menu

    Refer to LAMP TIME: When set, this function displays the total time the projector lamp has been used since new. Reset LAMP TIME [Use this function only when the lamp has been replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed.

  • Page 8: What To Do When You Think A Machine Defect Has Occurred

    WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED Related Messages When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. Message CHANGE THE LAMP AFTER REPLACING LAMP,...

  • Page 9: Regarding The Indicator Lamps

    Regarding the Indicator Lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table. POWER LAMP TEMP indicator indicator indicator...

  • Page 10: Phenomena That May Easily Be Mistaken For Machine Defects

    WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued) Phenomena That May Easily Be Mistaken for Machine Defects Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Phenomenon Cases not involving a machine defect The main power source is not ON.

  • Page 11: Specifications

    Size Weight (mass) Ports Optional Parts Dimension Diagram Specification Liquid crystal projector 2.5 cm (0.99 type) TFT active matrix 786,432 pixels (1024 horizontal x 768 vertical) Zoom lens F=1.7 ~ 2.4 f=30.5 ~ 45.8 mm 275 W UHB 1.0W + 1.0W (Stereo) AC100 ~ 120V, 4.7A / AC220 ~ 240V, 2.0A...

  • Page 12: Warranty And After-Service

    WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the “WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.
  • Page 13 TECHNICAL TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENT RGB IN [1]/[2] RGB OUT D-sub 15-pin Shrink Pin No Signal Pin No Video input Red Video input Green Video input Blue Ground Ground Red Ground Green Ground Blue signal Terminal BNC (RGB) RGB signal (R,G,B,H,V) input AUDIO IN 1...

  • Page 14: Example Of Computer Signal

    • Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. • Although the projector can display signals (except DVI input) with resolution up to UXGA (1,600 x 1,200), the signal will be converted to the projector’s panel resolution before being displayed.
  • Page 15 INITIAL SET SIGNALS The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. Back porch b Display interval c Sync a Computer / Horizontal signal timing (µs)

  • Page 16: Serial Mouse

    CONTROL Terminal D-sub 15-pin shrink jack Serial Mouse CONTROL Terminal D-sub 15-pin shrink jack USB Mouse USB jack (B type) PS/2 Mouse CONTROL Terminal D-sub 15-pin shrink jack Projector DATA Projector SEL0 Projector — DATA DATA USB cable Projector DATA SEL0...

  • Page 17: Communications Setting

    RS-232C COMMUNICATION (1) Turn off the projector and computer power supplies, and connect with the RS-232C adapter via the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the projector power supply.
  • Page 18 When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. Conversely, when the data length is shorter than indicated by the data length code, an error code will be returned to the projector.

  • Page 19: Command Data Chart

    Command data chart Names Operation type Blue White Black Blank Color MyScreen ORIGNAL Normal H Inverse Mirror V lnverse H&V Inverse Normal Freeze Freeze ORIGNAL Startup MyScreen English Français Deutsch Español Italiano Norsk Language Nederlands Português Magnify Increment Decrement Auto off Increment Decrement Brightness Reset...
  • Page 20 Command data chart (continued) Names Operation type H.Position Reset Execute H.Size Reset Execute Color Balance Execute R Reset Color Balance Execute B Reset Sharpness Reset Execute Color Reset Execute Tint Reset Execute Keystone_V Reset Execute Keystone_H Reset Execute Auto Adjust Execute Auto Keystone_V Execute...
  • Page 21 Names Operation type Color Balance B Increment Decrement Keystone_V Increment Decrement Keystone_H Increment Decrement 16:9 Aspect Small Default Picture Bottom Position at 16 : 9 or Small V.Position Increment Decrement H.Position Increment Decrement H.Size Increment Decrement H.Phase Increment Decrement Sharpness Increment Decrement Color...
  • Page 22 Command data chart (continued) Names Operation type Sync on G PinP Size PinP Position PinP Audio ch PinP Input WHISPER GAMMA Over Scan MyScreen Size MyScreen Lock Lamp Time Filter Time IR Remote Front IR Remote Rear IR Remote Top Header BE EF 06 00...
  • Page 23 Hitachi Sales Iberica S A Gran Via Carlos 111, 101, 1-1, 08028 Barcelona, Spain Tel: +34-3-330-8652 Fax: +34-3-339-7839 Hitachi Home Electronics Asia, (S) Pte Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318, Singapore Tel: +65-536-2520 Fax: +65-536-2521 Hitachi Sales (Malaysia) Sdn. Bhd.

This manual is also suitable for:

Cp-x880

Table of Contents