Advertisement
Quick Links
XH61V Quick Guide 【 English 】
__p
Front Panel
F1
F1. Power Switch / Power LED
F3
F2. HDD LED
F3. ODD and Front I/O Bay
F4. Slim ODD Bay
F5. USB2.0 Ports
F2
F6. Mic-In
F4
F7. Headphone
F5
F6
F7
F5
B1. S/PDIF Out Port
Back Panel
B2. Kensington® Lock Port
B3. COM1 Port
(RS232/RS422/RS485)
B4. COM2 Port (RS232)
B2
B5
B7
B12
B5. DVI-I Port
B6. HDMI Port
B7. LAN Ports
B8. USB3.0 Ports
B9. USB2.0 Ports
B10
B10. Mic-In Port
B11. Line-Out Port
B1
B8
B9 B10
B11
B13
B3
B4
B6
B12. Line-In Port
B13. DC Power Port
Motherboard Illustration
Intel H61 Chipset
LAN (x1) & USB3.0 (x2) Ports
LAN (x1) & USB2.0 (x2) Ports
Mic-In/ Line-Out/ Line-In Ports
C3
Clear CMOS Jumper-JP10
Audio Connector-JP4
C1
C6
USB Header-USB4
Serial ATA Connectors-SATA1,2,3
PCI-Express X4 Slot
LGA1155 Package CPU Socket
Jumper Settings
Audio Connector
C1
C2
Power Connector
Pin Assignments (JP4):
Pin Assignments (JP6):
1=MIC2_L
1=+HD_LED
2=AGND
2=PWR_LED
3=MIC2_R
3=-HD_LED
4=FRONT-JD
4=GND
5=LINE2-R
5=RST_SW
6=SENSE1_RETURN
6=PWR_SW
7=FRONT_SENSE
7=GND
8=KEY
8=GND
9=LINE2-L
9=NC
10=SENSE2_RETURN
10=KEY
1
2
3
4
5
6
7
8
9
10
C3
Clear CMOS Jumper
Pin Assignments (JP10):
1=UL_BAT_PWR
2=-RTCRST
Pin1-2
3=-RTCBTN
(BAT_POWER Mode)
C4
FAN Connectors
C5
SATA Power Connector
Pin Assignments (J1):
PWM_CTRL
1=GND
SPEED_SENSE
2=GND
3=+5V
+12V
4=+5V
Ground
CUP_FAN/SYS_FAN
USB Headers
C6
Pin Assignments (USB1/USB2/USB4):
1=5V_USB
2=5V_USB
3=USB A-
4=USB B-
5=USB A+
6=USB B+
7=GND
8=GND
9=NC
10=NC
Support RS232 Back panel
C7
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is +5V
IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is +5V
IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V
Pin Assignments (JP3):
1=-XRI1
2=COM_-XRI1
3=-XRI2
4=COM_-XRI2
5=+5V
6=+5V
7=COM1_PWR
8=COM2_PWR
9=+12V
10=+12V
C8
TPM Header (LPC)
DVI-I & HDMI Ports
Pin Assignments (JP1):
COM (x2) Ports
1=+12V
11=NC
S/PDIF Out Port
2=5V
12=3VSB
3=5VSB
13=RI
4=SERIRQ
14=LDRQ
ATX Power Connector-CN8
5=CLK-48M
15=PME
6=CLK-33M
16=LAD1
Support RS232 Back panel
C7
7=SIORST#
17=LAD0
Independent External Power
8=LFRAME
18=+3.3V
12V/5V-JP3
9=LAD3
19=GND
TPM Header (LPC)-JP1
C8
10=LAD2
20=NC
Mini PCIE Slot
Safety Information
Fan Connector-SYS_FAN
C4
Read the following precautions before setting up a Shuttle XPC.
SATA Power Connector-J1
C5
CAUTION
Incorrectly replacing the battery may damage this computer.
DDR3 SODIMM slots
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer's instructions.
USB Headers-USB1,USB2
C6
Laser compliance statement
The optical disc drive in this PC is a laser product.
Power Connector-JP6
C2
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
Fan Connector-CPU_FAN
C4
CAUTION： INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
62R-XH61V0-0601
XH61V
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
A. Begin Installation
For safety reasons, please ensure that the power cord is discon-
nected before opening the case.
1. Unscrew the two thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
2
1
2
4
6 8
10
3. Unfasten the racks mount screws and remove the racks.
1
3
5 7
9
Pin2-3
(Clear CMOS Mode)
4
3
HDD Rack
2
B. CPU and ICE Module Installation
1
1. Unfasten the four ICE module attachment screws.
Rotating the fastener along the direction of arrow is to remove
the ICE module, on the contrary, is to install.
1
2
3
4
5
6
3
1
7
8
9
10
4
2
2. Remove the ICE module from the chassis and put it aside.
Please note this 1155 pin socket bends easily. Always apply
extreme care and little force when installing a CPU and limit the
number of times you remove or exchange it. Before installation,
make sure to turn off the computer and unplug the power cord
from the mains to avoid damage.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
1
2
3. First unlock and raise the socket lever.
3
4
5
6
7
8
9
10
1
11
4. Lift the metal load plate on the CPU socket. Tear off the protective
2
12
membrane from the bottom of ICE module. Remove the protective
3
13
socket mylar from the CPU socket.
4
14
5
15
6
16
7
17
8
18
9
19
Remove the
protective
10
20
membrane
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
5. Orientate the CPU and socket and please align the CPU notches with
the socket alignment keys. Make sure the CPU is perfectly horizontal,
insert it into the socket.
Triangle Pin1
Marking on the CPU
Socket
1155
CPU
Notch on the CPU/
Alignment Key of the
CPU Socket
Please be aware of the CPU orientation, DO NOT force the CPU into
the socket to avoid bending of pins on the socket and damage of CPU!
L
The product's color and specification will depend on the actual shipping product.
6. Close the metal load plate, lower the CPU socket lever and lock in place.
7. Spread thermal paste evenly on the CPU surface.
Metal load plate
Thermal Paste
application area
Retention tab
Load lever
Please do not apply excess amount of thermal paste.
8. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
3
1
4
2
C. Memory Module Installation
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
SODIMM slot
notch
ODD Rack
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
1
2
45-degree
angle
3
Latch
Latch
5. Repeat the above steps to install additional memory modules, if required.
D. Component Installation
1. Install the Mini PCIE card into the Mini PCIE slot and secure with
screws.
Metal load
plate
2. Untie all cables for easier installation.
Purse lock
3. Place the slimline DVD drive in the rack and fasten it with the four
screws from the sides.
4. Slide the rack downward and forward and refasten it using the two
screws.
5. Connect the ODD cable and power cable to optical drive.
Slimline SATA Cable
6. Place the HDD in the rack and secure with the four screws from the side.
7. Connect the Serial ATA and power cables to the HDD.
Serial ATA Cable
Serial ATA Power Cable
8. Slide the rack in the chassis and refasten the two screws.
E. Complete
1. Replace the cover and refasten the thumbscrews.
2 . Complete.
Please load the optimized BIOS settings.
53R-XH61V3-2001
Advertisement
