Westerbeke 5.5KW EDC 60HZ Operator's Manual page 46

LAY-UP
&
RECOMMIS IONING
Starter Motor
Lubrication and cleaning of the starter drive pinion is advisable,
if access to the starter permits its easy removal. Make sure the
battery connections are shut off before attempting to remove
the starter. Take care in properly replacing any electrical
connections removed from the starter.
Cylinder lubrication [Diesel]
tryou
anti~ipate
a long lay-up period (12 months or more)
WEs1ERBEKE recommends removing the fuel injectors for
access to the cylinders. Squirt light lubricating oil into the
cylinders to prevent the piston rings from sticking to the
Cylinder walls.
Make sure you have a replacements for the injector and return
line sealing washers.
Intake Manifold [Gasoline]
Clean the filter screen in the flame arrester, and place a clean
cloth lightly soaked in lube oil around the flame arrester
to
block any opening. Also place an oil-soaked cloth in the
through-hull exhaust port, Make a note to remove cloths prior
to start-up!
tylinder Lubrication [Gasoline]
Spray fogging oil into the open air intake, with the flame
arrester removed, while the engine is running. The fogging oil
will stall out the engine and coat the valves, cylinders and spark
plugs for winter protection.
NOTE: The spark plugs will need to be removedfor cleaning
and re-gapping at spring commissioning.
Batteries
If batteries are to be left on board during the lay-up period,
make sure that they are fully charged, and will remain that way,
to prevent them from freezing. If there is any doubt that the
batteries will not remain fully charged, or that they will be
subjected to severe environmental conditions, remove the
batteries and store them in a warmer, more compatible
environment.
A
WARNING:
Lead acid batteries emit hydrogen, a
highly-explosive gas, which can be ignited by electrical
arcing or a lighted cigarette, Cigar, or pipe. Do not
smoke or allow an open game neal the battery being
serviced. Shut off all electrical equipment in the vicinity
to prevent electrical arcing during servicing.
Transmission [Propulsion Engine
I
Check or change the fluid in the transmission as required Wipe
off grime and grease and touch up any unpainted areas .. Protect
the coupling and the output flange with an anti-corrosion
coating. Check that the transmission vent is open. For
additional information, refer to the TRANSMISSION SECTION.
Lay-up ti provides a good opportunity to inspect your
Westerbek engine to see if external items such as drive belts
or coolant oses need replacement. Check your basic spares
kit and ord r items not on hand, or replace those items used
during the ay-up, such as filters and zinc anodes. Refer to the
SPARE B
TS section of this manual.
Recomm !ssioning
The reco!:· . ssioning of your Westerbeke engine after a
seasonalla -up generally follows the same procedures as
those desc bed in the PREPARATIONS FOR STARTING sec-
tion regarding preparation for starting and normal starts.
However,
s~me
of the lay-up procedures will need to be
counteracte~
before starting the engine.
1.
Remov~
the oil-soaked cloths from the intake manifold.
2. Removt, the raw water pump cover and gasket and
discard
~e
old gasket. Install the raw water pump impeller
removed during lay-up (or a replacement, if required).
Install ¢e raw water pump cover with a new cover gasket.
3. Reinstall the batteries that were removed during the
lay-upJ"nd reconnect the battery cables, making sure the
terminals are clean and that the connections are tight.
Check tp make sure that the batteries are fully charged.
A
CAUTION:
Wear rubber gloves, a lubber apron,
and eye protection when servicing batteries. Lead acid
batteries emit hydrogen, a highly explosive gas, which
can be ignited by electrical arCing
01
a lighted
Cigarette, cigar, or pipe. Do not smoke or allow an open
flame near the battery being serviced. Shut off all
electrical equipment in the vicinity to prevent electrical
arcing during serviCing.
4. Remove the spark plugs, wipe clean, re-gap, and install to
proper tightness [gasoline].
5. Check the condition of the zinc anode in the raw water
circuit and clean or replace the anode as needed. Note
that it is not necessary to flush the antifreeze/fresh water
solution from the raw water coolant system. When the
engine is put into operation, the system will self-flush in a
short period of time with no adverse affects. It is
advisable, as either an end of season or recommissioning
service, to inspect the area where the zinc is located in the
heat exchanger and clear any and all zinc debris from that
area.
6. Start the engine in accordance with procedures described
in the PREPARATIONS FOR STARTING section of this
manual.
Engines & Generators
40