I Preparation For Use; Turn On The Unit For The First Time; Clock Setup - Hitachi DV-PF35U Instruction Manual

Preparation for Use
Turn on the unit for the first
time
press VCR first.
* Refer to page 11 to switch between the VCR/DVD modes.
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section on page 7.
2
2
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
or
To select the desired language
To decide
3
3
AUTO SET UP
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD's ANT IN jack?
YES
Y es
Y es
Press MENU
to exit
• Refer to "Hint for Cable Box or
Satellite Box" section on page 7.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized in
this unit by using SKIP/CH (i/K or j/L).
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press Cursor B once again.
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by directly
entering channel using
the Number buttons on the remote
control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with 0 (For example: 02, 03,
04 and so on).
To Add or Delete Channels
1) Press MENU until the main menu
appears.
2) Select "CHANNEL SET UP" by
pressing Cursor K or L. Then, press
Cursor B.
3) Select "MANUAL SET UP" by
pressing Cursor K or L. Then, press
Cursor B.
4) Enter the desired channel number by
pressing Cursor K or L.
5) Add or Delete it from memory by
pressing Cursor { or B. so that
"ADD" or "DELETE" flashes on the
[ON]
TV screen accordingly.
6) Exit the preset mode by pressing
CLEAR/C.RESET.
To Preset the Channel Again
1) Press MENU until the main menu
appears.
2) Select "CHANNEL SET UP" by
pressing Cursor K or L. Then, press
Cursor B.
3) Select "AUTO SET UP" by pressing
CH 01
Cursor K or L. Then, press
Cursor B. After scanning, the tuner
stops on the lowest memorized
channel.
To Change the On-Screen Language
1) Press MENU until the main menu
appears.
2) Select "LANGUAGE SELECT" by
pressing Cursor K or L. Then, press
Cursor B.
3) Select "ENGLISH" , "FRANCAIS" or
"ESPAÑOL" by pressing Cursor K or
NO
L. Then, press CLEAR/C.RESET.
Hint
Hint
• If you accidentally select Spanish or
French but need English: Press MENU and
choose SELEC. IDIOMA, or
SELECTION LANGUE. Press
Cursor B, and select ENGLISH. Finally,
press CLEAR/C.RESET.
Clock Set Up
press
1
1
MENU
or
VCR first.
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
CLOCK SET screen
appears when you press
MENU. In this case, go
to step [2].
To decide
– 12 –
2
2
CLOCK SET
MONTH DAY
or
0 3 / – –
HOUR MINUTE
– – : – –
Select the current month
To decide
3
3
CLOCK SET
MONTH DAY
or
0 3 / 1 5
HOUR MINUTE
– – : – –
Select the current day
To decide
4
4
CLOCK SET
or
MONTH DAY
0 3 / 1 5
HOUR MINUTE
– – : – –
Select the current year
To decide
5
5
CLOCK SET
or MONTH DAY
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE
0 5 : – –
Select the current hour
To decide
6
6
CLOCK SET
MONTH DAY
or
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE
0 5 : 4 0
Select the current minute
To decide
7
7
CLOCK SET
MONTH DAY
0 3 / 1 5 TUE 2 0 0 5
or
HOUR MINUTE
0 5 : 4 0
Select "AM" or "PM"
8
8
To exit the CLOCK SET
screen.
CLEAR
or C.RESET
Hint
Hint
• To go back one step, press Cursor s
(during the steps [2] to [7].)
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
YEAR
– – – –
AM/PM
– –
YEAR
– – – –
AM/PM
– –
YEAR
2 0 0 5
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
– –
YEAR
AM/PM
P M AM
B PM
EN