Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SIIG 13"
Summary of Contents for SIIG 13"
-
Page 1: Installation Instructions
Triple Monitor Desk Stand - 13" to 24" Installation Instructions 04-0884A... -
Page 2: Safety Information
Unpacking • Carefully remove the contents and lay out on cardboard or other protective surface • Check package contents against the parts list to ensure that all components were received undamaged. Do not use damaged or defective parts • Carefully read all instructions before attempting installation Safety Information •... -
Page 3: Installation
Installation The Monitor Desk Stand can be free standing (Weighted Base Installation) or permanently attached to the desktop (Grommet Hole Installation). Step 1 - Mounting the Tube Support 1a) Weighted Base Installation For free standing, simply mount the 48mm Tube Support (a) to the Weighted Base (b) using M6x29 Bolts (j) then slide the Decorative Cover (k) onto the tube support as show in Figure 1a. - Page 4 1b) Grommet Hole Installation This installation requires you to either drill a 3/8" (10mm) diameter hole through the desktop or use an existing grommet hole. If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing. Mount the 48mm Tube Support (a) using Grommet Bolt (m), Grommet Plate (l) and secure with Wing Nut (n), then slide the Decorative Cover (k) onto the tube support as shown in Figure 1b.
- Page 5 Step 2 - Assemble Curved Arms and Install it onto the Tube Support Assemble the Curved Arms (d), Arm Connector Plate (e), Arm Clamp (f) and fasten with M6x25 Bolts (g) and M6 Washers (h) using Allen Key (o) as shown in Figure 2a. Important: Position the Arm Connector Plate (e) so that the screw holes are oriented to the bottom.
- Page 6 Mount the Arm Assembly to the tube support, fasten it using M8x10 Bolts (t) with Allen Key (o) and insert the Wire Clips (u) as shown in Figure 2b. Then continue to Step 3. Figure 2b...
- Page 7 Step 3 - Mounting the VESA Plate to the Monitor 3a) For Flat Back Monitors Mount the VESA Plates (c1 & c2) using M4x12 Bolts(q) and M4 Washers (p) as shown in Figure 3a. Then continue to Step 4. Figure 3a...
- Page 8 3b) For Curved Back Monitors Mount the VESA Plates (c1 & c2) using M4x30 Bolts(r) and M4 Washers (p) as shown in Figure 3b. Then continue to Step 4. Figure 3b...
- Page 9 Step 4 - Mounting the Monitors and Adjusting the Tilt Angle Attach the Middle VESA Plate (c2) with Monitor Assembly and secure it using M4x16 Bolt with Washers (v), then slide the Side VESA Plate (c1) with Monitor Assemblies onto the Arm Assembly and secure by rotating the Plastic Knob.
- Page 10 Adjust the monitor's tilt angle, use the Allen Key (o) to loosen the Grub Screw, then tighten the Grub Screw to fix the tilt angle as shown in Figure 4b. Figure 4b...
-
Page 11: Maintenance
Step 5 - Final Adjustment and Cable Management Adjusting the Height of the Monitors Using a Phillips screw driver, loosen the 2 Side Screws (one located on each side) on the VESA Plate with Monitor Assembly, then turn the Height Adjustment Screw clockwise to raise or counter clockwise to lower the monitor. -
Page 12: Technical Support And Warranty
Triple Monitor Desk Stand 13" to 24" Triple Monitor Desk Stand - 13" to 24" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are for identification only and may be trademarks of their respective owners.
Need help?
Do you have a question about the 13" and is the answer not in the manual?
Questions and answers