Table of Contents
Advertisement
Quick Links
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Chauvet MiN Laser FX 2.0
Summary of Contents for Chauvet MiN Laser FX 2.0
- Page 1 LASER LIGHT AVOID DIRECT EYE EXPOSURE CLASS 3R LASER PRODUCT CLASSIFIED PER EN/IEC 60825-1:2007 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated User Manual June 24, 2007. ...
-
Page 2: Table Of Contents
General Troubleshooting ............................13 Product Maintenance ............................... 14 Returns Procedure ..............................15 Contact Information ..............................15 6. Technical Specifications ............................16 Contact Information World Headquarters United Kingdom & Ireland CHAUVET® CHAUVET® Europe Ltd. General Information General Information Address: 5200 NW 108th Avenue Address: Unit 1C Sunrise, FL 33351 Brookhill Road ... -
Page 3: Before You Begin
CHAUVET®, upon receipt of the damaged merchandise. Failure to do so in a timely manner may invalidate your claim with the carrier. In addition, retain the container and all the packing material for inspection. -
Page 4: Safety Instructions
Safety Instructions Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document. ... -
Page 5: Non Interlocked Housing Warning
Non Interlocked Housing Warning This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels, accessible if the unit is opened, can cause instant blindness, skin burns, and fires. -
Page 6: Laser Safety Label Reproduction
Laser Safety Label Reproduction Front Rear Bottom MinLasers 2.0 User Manual August 2011... -
Page 7: Laser Emission Data
LASER EXPOSURE Laser light - Avoid direct eye contact! Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.laserinstitute.org. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. -
Page 8: Introduction
2. I NTRODUCTION Product Overview Mode Button Microphone Wireless Remote Receiver Indicator Laser Output Green Laser Dimmer 12 V Power Cooling Fan MinLasers 2.0 User Manual August 2011... -
Page 9: Setup
This product includes an external power supply which is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. Only use the included power supply! To obtain a replacement power supply, contact Chauvet®. To determine the power requirements for a particular product, see the label affixed to the Power Supply back plate of the product or refer to the product’s specifications chart. - Page 10 Floor Stand, Flexible Feet (3) Coupler Clamp MinLasers 2.0 User Manual August 2011...
-
Page 11: Proper Usage
Proper Usage This product is for overhead mounting only. For safety purposes, CHAUVET® recommends mounting your lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety cables. You can obtain appropriate mounting hardware from your lighting vendor. -
Page 12: Operating Instructions
4. O PERATING NSTRUCTIONS Manual Mode Access the four different operating modes available in this product by using the <MODE> button on the front panel. Pressing and holding the <MODE> button for 2.5 seconds will turn the product on or off. Press <MODE>... -
Page 13: Appendix
#32. Keep DMX cables separated from Interference from AC wires power cables or black lights. If you still have a problem after trying the above solutions, please contact CHAUVET® Technical Support. MinLasers 2.0 User Manual August 2011... -
Page 14: Product Maintenance
Product Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, you should clean your lighting products at least twice a month. -
Page 15: Returns Procedure
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be the customer’s responsibility. As a suggestion, proper UPS packing or double-boxing is always a safe method to use. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). Contact Information World Headquarters United Kingdom &... -
Page 16: Technical Specifications
Operating current (units) 0.1A 0.1 A Power I/O Input Output Connectors Edison (USA) Cord plug Edison (USA) Light Source MiN Laser FX 2.0 Type Power Wavelength MiN Laser RGX 2.0 Laser (green) 50 mW 532 nm Laser (red) 100 mW 650 nm...