Listening Through A Receiver; Check Points Before Requesting Service - Samsung LCD TV User Manual

listening through a receiver

You can listen to sound through a receiver instead of the tV speaker.
1. Press the toolS button. Then Press the enter
CEC)".
Press the ▲ or ▼ button to select "Receiver", then press the enter
. Press the ◄ or ► button to select to "On", then press the enter
Now you can listen to sound through the receiver.
. Press the eXIt button to exit.
➣
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➣
If the receiver is exclusively for a home theatre only (supporting audio only), it may not
appear in the device list.
➣
In case of a content with copyright problem, listening through the receiver may not properly operate.
➣
If there is a power interruption to the TV when the "Receiver" is set to "On" (by disconnecting the power cord or a power
failure), the "TV Speaker" may be set to "Off" when you turn the TV on again. (see page 21)

Check Points before requesting Service

Symptom
anynet+ does not work.
I want to start anynet+.
I want to exit anynet+.
the Configuring anynet+
connection message appears
on the screen.
the anynet+ device does
not play.
the connected device is not
displayed.
the tV programme cannot be
recorded.
button to select "Anynet+(HDMI-
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device's Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work at a certain condition. (Searching channels, Operating WISELINK, Plug & Play,
etc.)
■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or
restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is
set to On in the Anynet+ Setup menu.
■ Press the tV button on the TV remote control to switch to TV. Then press the toolS button to show
the Anynet+ menu and select a menu you want.
■ Select View tV in Anynet+ menu.
■ Press the SourCe button on the TV remote control and select a device other than Anynet+ devices.
P /
■ Press any of and Pre-Ch such to change to the TV mode. (Note that the channel button
operates only when a tuner-embedded Anynet+ device is not connected.)
■ You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not
support Anynet+ functions.
■ If it is terminated by an abnormal situation such as disconnecting the HDMI 1.3 cable or power cord
or a power failure, please repeat the device scan.
Check whether the antenna jack on the recording device is properly connected.
english - 1
tV
button.
button.
move
return
P
View tV
Select Device

record

menu on Device

Device operation

receiver :off

Setup

enter