Bionaire BT440RCU Instruction page 2

p L E A S E R E A D A N D S AV E T H E S E
I M p O RTA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions 14. To disconnect, grip plug and pull from wall outlet.
should always be taken including the following: Never yank on cord.
15. Always use on a dry, level surface.
1. Read all instructions before using this appliance.
16. Do not operate fan until fully assembled with all
2. Use fan only for purposes described in the instruction
parts properly in place.
manual.
17. This product is intended for household use ONLY and
3. To protect against electrical shock do not immerse unit,
not for commercial or industrial applications.
plug or cord in water or spray with liquids and plug the
18. WARNING: To reduce the risk of electrical shock
appliance directly into a 120V AC electrical outlet.
and injury to persons, do not use in window.
4. Close supervision is necessary when any appliance is
19. WARNING: To reduce the risk of fire or electric
used by or near children.
shock, do not use this fan with any solid-state speed
5. Unplug from outlet when not in use, when moving
control device.
fan from one location to another, before putting on
20. This product employs overload protection (fuse). A
or taking off parts and before cleaning.
blown fuse indicates an overload or short-circuit
6. Avoid contact with moving parts.
situation. If the fuse blows, unplug the product from
7. Do not operate in the presence of explosive and/or
the outlet. Replace the fuse as per the user servicing
flammable fumes.
instructions (follow product marking for proper fuse
8. To avoid fire hazard, NEVER place the cord under
rating) and check the product. If the replacement fuse
rugs or any parts near an open flame, cooking or
blows, a short circuit may be present and the product
other heating appliance.
should be discarded or returned to an authorized
9. Do not operate any appliance with a damaged cord
service facility for examination and/or repair.
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
pLEASE READ AND SAVE
return to an authorized service facility for
examination and/or repair.
THESE IMpORTANT
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
SAFETY INSTRUCTIONS
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
INSTALLATION INSTRUCTION:
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
ASSEMbLY INSTRUCTIONS:
exposed to high traffic areas.
13. Do not use outdoors.
Estimated assembly time: 5-10 minutes
(tools required: Screwdriver)
THIS AppLIANCE HAS A pOLARIzED pLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMpT TO MODIFY THIS pLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
F E AT U R E S - O p E R AT I O N S
Figure 1
A
B
E
C
D
A. Control Panel D. Base Halves
B. Remote Control Storage E. Remote Control
(SEE FIGURE 1) C. Fan Housing
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROM
(SEE FIGURE 2)
THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
1. Assemble base halves around power cord. To secure the
base halves together, slide the posts of one base half
into the slots of the second base half. Refer to Figure 2.
2. Line up the screws holes of the base halves with the
holes located on the bottom of the fan housing.
Secure with the four screws included with the
product. Refer to Figure 2.
3. Turn fan right side up and place on a dry and level surface.
located on the control panel or remote control. When
Figure 2
turned on, the fan will randomly cycle through the three
speeds settings recreating a natural outdoor breeze.
6. To turn the fan off press and hold the power/speed button
(
NOTE: your fan features a LED display panel. When a specific
feature is activated on your fan, the LED display panel
will light up showing which features have been activated.
C
REMOTE CONTROL HANDSET:
NOTE: PLEASE REMOVE THE PROTECTIVE STICKER FROM
THE REMOTE CONTROL BATTERY BEFORE OPERATION.
This unit includes one lithium battery, CR2025/3V.
Remove battery before discarding the remote.
battery Replacement
a) Locate the battery compartment on the back of the
remote control handset. Slide the battery cover out
D
with your thumb.
b) Remove old battery.
c) Place new battery into battery compartment.
d) Slide battery compartment into the remote control
handset.
NOTES:
• Remove the battery from the equipment when it is not
being used for an extended period of time.
OpERATING INSTRUCTIONS:
(SEE FIGURE 3) • Remove the used battery promptly.
1. To control the power of the fan press the power/
Figure 3
speed button ( ) located on the control panel
or remote control.
2. To cycle through high, medium, and low speed
settings (3-2-1) press the power/speed button
( ) located on the control panel or remote
control.
3. To turn the oscillation on and off, press the oscillation
button ( ) located on the control panel or
remote control.
4. To set your fan to automatically shut off press the
timer button ( ) located on the control panel or the
remote control. When set, the fan will run and
automatically shut off after the set duration of time
(1, 2, 4, or 8 hours) has expired.
5. To activate the breeze mode, press the breeze button ( )
F E AT U R E S - O p E R AT I O N S
• Do not discard used batteries into household trash
containers. Contact your local government for disposal
or recycling practices in your area.
) located on the control panel or remote control.
FCC STATEMENT
potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(SEE FIGURE 3)
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. The product generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that the interference will not occur in a
particular installation. If the product does cause harmful
interference to radio or television reception, which can be
determined by turning the product on or off, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Control panel
B
A
A B E
C D
A. Oscillation Button B. Breeze Button C. Power/Speed Button D. LED Display Panel
Remote Control
E
C
E. Timer Button