Thank you for purchasing our product. Please read this User’s Manual before using the product. Change without Notice 16 Channel Digital Video Recorder User’s Manual...
1. Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This label may appear on the bottom of the unit due to space limitations. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be...
2. About this document Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users Manual. Pay particular attention to the parts that are marked NOTICE. Also, when connecting with external application, first turn the power OFF and follow manual instruction for appropriate installation.
5. Content Table 1. Safety Precautions…………………………………………….………………………….……………………. 2 2. About this document……………………………………………………………………………………………. 3 3. Before reading this document…………………………………………………………………………………. 3 4. Hardware ……………………………………………………………………………………………………….. 3 5. Content Table…………………….……….…………………………………………………………………….. 5 6. Unit Description of Front Panel……………………………………………………………………………….. 5 7. Unit Description of Rear Panel………………………………………………………………………………... 6 8.
6. Unit Description of Front Panel Removable Hard Disk 16 / 13 / 9 / 4 quarterly split screen button 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16 full screen button Picture freeze Picture zoom in Auto sequence Picture in picture / Select channel mode BUTTON Direction Button Up and Down / Record Stop, Playback Pause/step. Direction Button Left and Right / Fast and slow Reverse Fast/slow Forward Playback...
8. Installation Procedure 1) Camera Connection Connect the camera to the CAMERA INPUT LEVEL VIDEO MONITOR on the Rear Panel of the 16 CH DVR. VIDEO LENS AC24V/DC12 Rear part of CAMERA 2) Monitor Connection (Composite Connection Method) Connect the monitor to the MONITOR OUT on MONITOR the Rear Panel of the 16 CH DVR.
Page 8
NOTICE: Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND, and it is recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit. Internal Circuit Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V. 5) Network Connection DVR connects to LAN ETHERNET...
Page 9
7) Power Connection 1. +12VDC Connect the power to the POWER 2. +12VDC 3. +12VDC CONNECTION on the Rear Panel of the 4. RTN system, and turn on the switch. 8) Turn on the POWER. Make sure the adaptor is 12V/5A. 9) Detail setup in SYSTEM SETUP For detail setup, refer to the instruction of SYSTEM SETUP.
Picture Full screen or quarterly split screen display Press button, to display 16 / 13 / 9 / 4 quarterly split screen. Press numeric buttons to display the desired camera image in full screen. 1.) FREZZE Mode 1. In live and the quad mode press (FREEZE) button to freeze image.
Page 11
SEL (Select) >On the 13 / 9 / 4 split screen, press SEL can change the each channel order. Press SEL button to active the selection function. Turn the inner-shuttle or button to select the desired camera channel in split-1. Press change button to change the split-screen position.
Playback 1. Playback Mode 1) Press button to begin playback. (System will playback the images in backward) PLAY 2. T-SRH button PLAY SETUP PAGE 1) T-SRH: Playback by time search. EVENT LIST Press T-SRH button to active playback function. TIME LIST Press direction button PLAY END: RECYCLE UP/DOWN to choose...
Page 13
3) TIME LIST (Playback image by Time-Search): Recorded images list (by hours) TIME SEARCH LIST PAGE : CURSOR, : PAGE, ENTER: PLAY No items or page display limit. Items. DVR recording mode is continued. Press direction button UP/DOWN to choose items. Press values change button to change to next page.
9. FUNCTION SETUP LOGIN MENU 1) Press button to enter into menu. You could do the system function setup in MENU. 2) Password enter window pop-up: LOGIN DVR SYSTEM 1. Password (Account-Admin) : 44444 2. Password (Account-User) : 11111 PASSWORD xxxxx 3) Press numeric button to choose password then menu pop-up.
Basic Operation Press MENU button to enter MAIN SETUP PAGE. MAIN SETUP PAGE 1. HDD INFORMATION 2. DATE-TIME SETUP 3. DISPLAY SETUP 4. CAMERA SETUP 5. BUZZER SETUP 6. AUDIO SETUP 7. SYSTEM SETUP 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN 1) Use direction button up/down button to select setup item.
4. CAMERA SETUP MAIN SETUP PAGE CAMERA SETUP PAGE 1. HDD INFORMATION 1. COLOR SETUP 2. DATE-TIME SETUP 2. TITLE SETUP 3. DISPLAY SETUP 3. SCREEN POSITION SETUP 4. CAMERA SETUP 4. V-LOSS DISPLAY SETUP 5. BUZZER SETUP 6. AUDIO SETUP MENU, ESC: EXIT, ENTER: RUN 7.
Page 20
(2.) TITLE SETUP: Input TITLE of each camera. 7 characters can be input. CAMERA-TITLE SETUP PAGE CH01 (01 ) CH09 (09 ) CH02 (02 ) CH10 (10 ) CAMERA SETUP CH03 (03 ) CH11 (11 ) 1. COLOR SETUP CH04 (04 ) CH12 (12 ) 2.
Page 21
(3.) SCREEN POSITION SETUP **** SCREEN POSITION**** CAMERA SETUP 1. COLOR SETUP LEFT RIGHT 2. TITLE SETUP 3. SCREEN POSITION SETUP DOWN 4. V-LOSS DISPLAY SETUP ENTER for Default ESC to QUIT Press direction buttons up/down/left/right to move screen position. 2.
Page 22
(4.) V-LOSS DISPLAY SETUP VLOSS SETUP PAGE (Video Loss Detection) **VLOSS FUNCTION: VLOSS 01: VLOSS 09: CAMERA SETUP VLOSS 02: VLOSS 10: 1. COLOR SETUP VLOSS 03: VLOSS 11: 2. TITLE SETUP VLOSS 04: VLOSS 12: 3. SCREEN POSITION SETUP VLOSS 05: VLOSS 13: 4.
2. MOTION SETUP MOTION SETUP ADVANCED SETUP PAGE **MOTION FUNCTION ON 1. ALARM SETUP **CHANNEL NUMBER 1. DETECT NUMBER 2. MOTION SETUP 3. RECORD SETUP 2. SENSITIVITY 4. EVENT 3. VELOCITY 5. TCP-IP SETUP 4. MOTION ACTIVE 6. PASSWORD SETUP 5.
Page 28
> MOTION AREA SETUP < ****CH01 AREA MASK**** Press numeric to select channel. : WALK ON MODE 1.2.3.4: SELECT CHANNEL Press value change button to change mode. :MOVE SURSOR Press direction button to move sursor. ENTER: MASK OFF Press ENTER button to on mask function or off. ESC KEY: QUIT Press ESC button to quit.
Page 29
>MOTION RELAY SETUP< MOTION RELAY SETUP PAGE MOTION SETUP **MOTION FUNCTION **RELAY FUNCTION **CHANNEL NUMBER RELAY01 RELAY09 1. DETECT NUMBER RELAY02 RELAY10 2. SENSITIVITY RELAY03 RELAY11 3. VELOCITY RELAY04 RELAY12 4. MOTION ACTIVE RELAY05 RELAY13 5. RECORD DURATION RELAY06 RELAY14 6.
3. RECORD SETUP RECORD SETUP ADVANCED SETUP PAGE 1. HDD FULL 1. ALARM SETUP 2. RECORD SCHEDULE 2. MOTION SETUP 3. RECORD MOTION 3. RECORD SETUP 4. RECORD ALARM 4. EVENT 5. RECORD POWER ON 5. TCP-IP SETUP 6. RESOLUTION 6.
Page 31
>SCHEDULE SETUP< RECORD SETUP 1. HDD FULL Press direction buttons up/down to 2. RECORD SCHEDULE SCHEDULE items. 3. RECORD MOTION 4. RECORD ALARM Press values change button to change values. 5. RECORD POWER ON 6. RESOLUTION Factory default is everyday all schedules time on >SCHEDULE SETUP<...
7. HDD FORMAT ADVANCED SETUP PAGE 1. ALARM SETUP Press direction buttons up/down to 2. MOTION SETUP HDD FORMAT items position. 3. RECORD SETUP Press ENTER to in. 4. EVENT 5. TCP-IP SETUP 6. PASSWORD SETUP 7. HDD FORMAT 8. HDD AUTO DETECT 9.
Page 38
9. FACTORY DEFAULT ADVANCED SETUP PAGE 1. ALARM SETUP 2. MOTION SETUP Press direction buttons up/down to 3. RECORD SETUP FACTORY DEFAULT items position. 4. EVENT Press ENTER to in. 5. TCP-IP SETUP 6. PASSWORD SETUP 7. HDD FORMAT 8. HDD AUTO DETECT 9.
10. HDD BAY 1. HDD EXTENSION Default HDD included in DVR unit. 1) 1,2,3,or4 HDD as per customer requirement. 2) EIDE, 3.5 inch, 7200 rpm. 3) HDD capacity up to 120GB/unit. Compatibility with up to 120GB confirmed. 2. HDD BAY HDD Bay ( Tera-Tray ) In case 2 HDDs installed in a DVR unit is not sufficient and needs to increase storage capacity, connect HDD Bay to DVR unit.
Page 40
Hard Disk Master / Slave jumper pin define: HDD Bay , The hard disk jumper pin must be in Master if only one hard disk inside of HDD BAY. Master or Slave jumper pin define must check the each company description. Otherwise it makes DVR hard disk work wrong.
11. Specification and configuration 16CH Digital Video Recorder Model NTSC/PAL System Video I/F 16 CH Input 1.0Vp-p, 75ohm unbalanced (BNC Type) Input 1 Output CVBS: 1.0Vp-p, 75 ohm unbalanced (BNC Type) Output 480TV Lines Horizontal Resolution More then 40dB S/N Ratio 16.7 Million Color Monitoring Method...
Page 42
2. DVR system Remocon Camera 1~16 Sensor Alarm Internet TCP/IP Printer RS232C HDD BAY 1~2 TV Monitor S-Video Monitor Notice: RS-232C is for ISP version update. PIN No. Definition C o m m P o r t RS-232C...
13. Remote Viewer General description: TCP/IP option of DVR and enables users to view live pictures, search recorded pictures, far apart from the DVR unit, and users can store selected recorded pictures on HDD of client PC. DVR does not adopted web browser method for access to DVR unit via Internet line, and you must install Remote Viewer software included in the package on client PC before you try to access to DVR unit over IP network.
Page 44
6 Status window. It shows Date and Time. Further it displays “connection established” and a circular fan on the left bottom is rotating when connection button is activated, or ”Waiting for connection” when disconnection button is activated. 7 Set button. 3 different set buttons a) Setting : It is in the middle of 3 buttons.
Page 45
Run in full screen mode: Full screen monitor display. Receive events: When alarm and motion and video loss, the DVR status will display. 8 PTZ control. This function is not available. SAVE OPTION: Choose the hard disk path where you are going to save. 2.
Page 46
6 : Time selection button. You can set time to search by dragging yellow mover to the left or right. See time displayed in green color and find and exact time from which you search. 7 : Start and end of recording. It shows time from which recording started and recording ended. Further it show time from which search will start.
Page 47
10 : Calendar. You can select date and time to search pictures recorded at selected time and date. You can refer to start and end of recording in 7. Notice : We recommend you to click operation buttons one after the other with enough time interval to give long enough time for DVR unit to execute commands from client PC.
Page 48
13. Configuration Chart 1.Hardware Status Site Name Technician DVR Serial# Installation Date Hard Disk Serial# Password Item Verify Date Comments/Status 1.Power Core 2.Remote Controller 3.Hard Disk Removable hard drive 4.LED Indicators Power 5.RS232 6.Alarm 7.Video Input/ Output Cam1/Looping Cam2/Looping Cam3/Looping Cam4/Looping Cam5/Looping Cam6/Looping...
2.System Configuration Site Name Hard Disk Model Model Name Hard Disk Number DVR Serial# Hard Disk Serial# Password Technician Configuration Check List ITEM Setting 1 Setting 2 Setting 3 Setting 4 Date 1.Display Setup Time/Date Camera Title PB Time/Date PB Camera Tile DVR Status Border Set 2.Camera Setup...
Page 50
MAC Address 7.Miscellaneour Setup Buzzer Setup ID/PW Setup Image Backup Setup HDD Information HDD Format RS-485 ID Sequence Interval Factory Default...