Table of Contents
Advertisement
Assigning the [S1] [S2] buttons When S1/S2 Mode is Set to
"SYSTEM"
When this is set to SYSTEM, "S1/S2 Setting" appears in the lower right
of the screen. Pressing the [TONE EDIT] (S1/S2 Setting) button at this
point calls up the screen for the function assigned to the [S1] [S2]
buttons.
Parameter
Value
00: OFF
01:
COUPLE +1OCT
02:
COUPLE -1OCT
03:
COUPLE +2OCT
04:
COUPLE -2OCT
05:
COUPLE +5TH
06:
COUPLE -4TH
07:
OCTAVE UP
08:
OCTAVE DOWN
09:
S1/S2
START/STOP
10:
TAP TEMPO
11:
SONG PLY/STP
12:
SONG RESET
13:
SONG BWD
14:
SONG FWD
15:
MFX SW
16:
ROTARY SPEED
17:
LIVE SET UP
18:
LIVE SET DOWN
19:
PANEL LOCK
Function/Parameter Setting
Changed
No control
Playing a key will also sound
an additional note one octave
higher.
Playing a key will also sound an
additional note one octave lower.
Playing a key will also sound
an additional note two octave
higher.
Playing a key will also sound an
additional note two octave lower.
Playing a key will also sound
an additional note a fifth (7
semitones) higher.
Playing a key will also sound
an additional note a fourth (5
semitones) lower.
Each time you press the button,
the keyboard range will rise by
an octave (maximum 4 octaves).
Each time you press the button,
the keyboard range will lower by
an octave (maximum 4 octaves).
The external sequencer will start/
stop.
The tempo will be modified to
the interval at which you press
the button.
Starts and stops the song (p. 37).
Returns you to the beginning of
the song.
Rewinds the song.
Fast-forwards the song.
Turns on/off multi-effect (p. 39).
When using the rotary
effect, switches the rotary effect
between slow and fast.
Switches the Live Sets in
ascending order.
Switches the Live Sets in
descending order.
Switches the Panel Lock (p. 35) on
and off.
Detailed Settings for Each Function
Using Program Change Messages to Switch
LIVE SETs (LIVE SET Ctrl Ch)
You can switch the RD-300NX's Live Sets with MIDI messages from an
external MIDI device.
Parameter
Value
1–16
LIVE SET Ctrl Ch
(LIVE SET Control
Channel)
OFF
NOTE
When the LIVE SET Control Channel settings are transmitted along
with the part's MIDI receive channel, switching of Live Sets takes
priority over the switching of tones.
You can download the materials on MIDI from the Roland website.
Roland website:
http://www.roland.com/
Selecting the USB Driver (USB Driver)
Refer to the "Switching USB Drivers" (p. 81)
Switching the USB Memory Mode
(USB Memory Mode)
Refer to the "Changing the USB Memory Setting" (p. 81)
Switching the Pedal's Polarity
(Damper/FC1/FC2 Polarity)
Switch the polarity of pedals connected to the RD-300NX.
This can be set individually for each of the Pedal jacks on the rear panel
(FC1, FC2, DAMPER).
On some pedals, the electrical signal output by the pedal when it is
pressed or released is the opposite of other pedals. If your pedal has an
effect opposite of what you expect, set this parameter to REVERSE.
If you are using a Roland pedal (that has no polarity switch), set this
parameter to STANDARD.
Parameter
Value
Damper Polarity
FC1 Polarity
STND (STANDARD), REV (REVERSE)
FC2 Polarity
Description
Set the MIDI Receive channel for
receiving the MIDI mes-
sages (Bank Select and Program
Change) from the external MIDI
device to be used for switching
Live Sets.
When not switching Live Sets
from an external MIDI device, set
this to OFF.
61
Advertisement
Table of Contents
