Soundstream Tarantula AL.2 Installation Manual
  1. Manuals
  2. Brands
  3. Soundstream Manuals
  4. Car Alarm
  5. Tarantula AL.2
  6. Installation manual
Soundstream Tarantula AL.2 Installation Manual

Soundstream Tarantula AL.2 Installation Manual

Tarantula auto security system
Hide thumbs Also See for Tarantula AL.2:
Table of Contents

Advertisement

Quick Links

See also: User's Operation Manual
REV.5
AL.2
AUTO SECURITY SYSTEM
www.security.soundstream.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user's authority to operate
this device.
INSTALLATION GUIDE
FCC ID NOTICE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Tarantula AL.2 and is the answer not in the manual?

Questions and answers

Related Manuals for Soundstream Tarantula AL.2

Summary of Contents for Soundstream Tarantula AL.2

  • Page 1 REV.5 AL.2 AUTO SECURITY SYSTEM INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

  • Page 2: Table Of Contents

    AL.2 PAGE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS Wire Diagram..............Page 3 Program Mode...............Page 4 Enter Program Mode Programing Chart............Page 5 Program Menu 1 Page 5 Program Menu 2 Page 5 Wire Description............Page 6-8 Transmitter Programming..........Page 9...

  • Page 3: Wire Diagram

    AL.2 PAGE 3 WIRE DIAGRAM INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 Optional Communication Port LED / VALET Switch RF Antenna Pin 4 - Red - 12volt Output for Sensor Pin 3 - Black - Ground Output for Sensor Pin 2 - Green - Full Alarm Trigger Input (-)

  • Page 4: Program Mode

    AL.2 PAGE 4 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On. (Leave the key in the ON position) 2 - Press and release the Program Switch 1 time.
  • Page 5 AL.2 PAGE 5 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 1 SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 LED FLASHES DESCRIPTION 1 CHIRP 2 CHIRPS 3 CHIRPS IGNITION IGNITION AUTO-LOCK & IGNITION AUTO-LOCK IGNITION AUTO-LOCK...

  • Page 6: Wire Description

    AL.2 PAGE 6 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING WIRE DESCRIPTION Pin 3- Blue Wire- Negative Unlock Output (-250ma Output) Pin 2- 12volt Output for Voltage Inverter. Pin 1- Green Wire- Negative Lock Output (-250ma Output) Pin 9- White/Green Wire- 2nd Unlock/ (-) When Disarmed Output...
  • Page 7 AL.2 PAGE 7 SYSTEM WIRING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 WIRE DESCRIPTION (-) Output When Unlock Is Pressed For 1 Second. (Programmable) Blue (+) LOW CURRENT OUTPUT FOR VOLTAGE INVERTER ONLY. (-) Output When Lock Is Pressed For One Second. (Programmable) Green (-) 2nd Unlock Output / Ground Output When Disarmed.
  • Page 8 AL.2 PAGE 8 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING WIRE DESCRIPTION SHOCK SENSOR INPUT The supplied dual stage shock sensor connects directly to the module. If a secondary sensor is being installed the wiring for the connector is as follows.

  • Page 9: Transmitter Programming

    AL.2 PAGE 9 TRANSMITTER PROGRAMMING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAMMING TRANSMITTERS The system can lean up to 3 different remote’s. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is programmed all previous remote’s are deleted.

  • Page 10: Shock Sensor Programing

    AL.2 PAGE 10 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SHOCK SENSOR SHOCK SENSOR CONNECTION The supplied dual stage shock sensor connect’s directly to the shock sensor connect on the alarm module. The adjustment screw on the sensor will increase or decrease the sensitivity. The first and second stage are controlled by the same adjustment screw.

  • Page 11: Diagnostics

    AL.2 PAGE 11 DIAGNOSTICS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ALARM STATUS / DIAGNOSTICS If the alarm system is triggered, the system will retain in memory the cause of the trigger. When disarming the alarm, the siren/horn will chirp 3 times to indicate the alarm had been triggered.
  • Page 12 AL.2 PAGE 12 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM OPERATIONS CHIRP / BUTTON BUTTON PRESS SYSTEM FUNCTION FLASH 1 SECOND LOCK / ARM ALARM 3 SECONDS ACTIVATE PANIC PRESS THEN ACTIVATE CONSTANT LOCK RELEASE THEN OUTPUT ** LOCK PRESS &...
  • Page 13 AL.2 PAGE 13 SYSTEM OPERATIONS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ARMS / LOCKS AND TURNS OFF PRESS AND RELEASE SHOCK SENSOR LOCK THEN PRESS AND RELEASE TRUNK (FOR 1 ARM CYCLE ONLY) SECOND CAR OPERATION/ PADLOC. SEE TRANSMITTER PROGRAMMING FOR INFORMATION ON PROGRAMMING THIS FEATURE.

  • Page 14: Anti Car Jack Mode

    AL.2 PAGE 14 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ANTI CAR JACK MODE ACTIVATING ANTI CAR JACK MODE This feature requires that the user must be fully aware of the operation of this feature. If the system goes into full alarm the remote’s will no longer function until the Anti Car Jack Feature is disabled.
  • Page 15 Soundstream. After an initial period of 2 years from the original date of installation, Soundstream reserves the right, at its sole discretion, to charge a warranty processing fee of $30.00 USD. Soundstream does not cover the cost for return freight on warranty items. This cost is the sole responsibility of the purchaser.
  • Page 16 www.security.soundstream.com...

Table of Contents