Advertisement
Connecting the DC Adapter
Connect the DC adapter to the B-EP2DL or B-EP4DL series printer using the
following procedure.
Please note that the procedure is explained supposing the DC adapter has been
installed on a vehicle.
For how to check the charge status, please refer to the Owner's Manual of the
B-EP2D/B-EP4DL series Owner's Manual.
1 Make sure that the battery pack is in the printer
2 Connect the plug of this device to the DCIN connector on the printer.
The external power source symbol is displayed on the printer LCD, and battery
charge starts. Whether the battery charge is required or not is automatically
determined by the printer.
3. When the charging is completed, disconnect the device from the printer.
NOTE:
Charging time may differ depending on the condition of the battery pack or the
operating temperature.
INPUT LED
OUTPUT LED
Portable Printer
LED
INPUT LED
Lights up in green when the input voltage is ON
OUTPUT LED
Lights up in red when the output voltage is ON.
Troubleshooting
If you have any problems on this product or portable printer when in use, please check the
following point first. If a problem cannot be solved by taking actions described below, disconnect
this product from the printer and contact the dealer or an authorized TOSHIBA TEC service
representative for assistance.
Symptom
• The adapter is not connected to the vehicle properly.
The INPUT LED (green) does not
⇒Ask an expertised person for connection.
light up.
• The supply voltage drops.
⇒The input power source has a problem. Please contact
• Check if the INPUT LED lights up or not.
The OUTPUT LED (orange) does
⇒When the INPUT LED is unlit, check the input power
not light up.
⇒When the INPUT LED is lit, the output power source has
• The DC adapter is not connected to the printer.
The CHARGE lamp on the printer
⇒Firmly connect the adapter to the printer
does not light up.
• The battery pack is not loaded in the printer.
⇒ Load a battery pack in the printer.
• A fully charged battery pack is in the printer.
⇒ The CHARGE lam does not light up if the battery pack
• The ambient temperature does not fall within the range
from 0ºC to 40ºC.
⇒The battery is not charged when the ambient
Connected to a power
source
DC Adapter
Plug
DCIN Connector
Status
8
Cause and resolution
a maintenance company for checking the supply
voltage.
source.
a problem. Please contact a maintenance company for
checking the supply voltage.
is already fully charged.
temperature is out of the operating temperature.
10
Wiring Diagram
• Polarity of the cable
White: Positive electrode
• Example of connection
NOTE:
Be sure to insert a protection circuit, such as a
fuse and a circuit breaker.
Battery
(12 to 48V)
(Capacity: 5A)
Terminal base
Mounting Diagram
Secure the DC adapter with two M5 screws.
70.00
Specifications
Model:
B-EP800-DC48-QM-R
Connectable device:
B-EP2DL or B-EP4DL series
Input power voltage:
DC 12 to 48V (e.g. Fork lift battery)
Absolute max. rated voltage: DC 10 to 60V
Output voltage and current: DC. 19.5V 1.7A
Operating temperature:
0ºC to 40ºC (32ºF to 104ºF)
Operating humidity:
10 to 90% (No condensation)
Storage temperature:
-20ºC to 70ºC (-4ºF to 158ºF)
Storage humidity:
10 to 90% (No condensation)
Cord length:
Printer side: Approx. 1.8m Vehicle battery side:
Approx. 3.5m
Dimensions:
92.5 x 55 x 142.5 mm (w/h/d) (Excluding the
projecting parts.)
(3.64" x 2.17" x 5.61")
Weight:
Approx. 530 g (18.7 oz)
Accessories:
Owner's Manual x 1
NOTE: Design and specifications are subject to change without notice.
Black: GND
DC Adapter
Printer
IN
OUT
DC IN
70.00
9
11
Advertisement
