Table of Contents
Advertisement
MAINTENANCE
After the chimney has been cleaned clean out the firebox
and carefully replace the rear half of the baffle. Check to
see that both pieces of the baffle are down on the steel
baffle and pushed all the way to the rear of the firebox.
Figure 27
Figure 27 -
Replace Baffle
REplACE glASS ONlY WITh hIgh TEMpERATuRE
ST1088
CERAMIC AvA/IlAblE FROM YOuR lOCAl MhSC
replace baffle
dEAlER
Use of glass or other components from alternative sources
may cause a safety hazard and may void your warranty.
The following use and safety tips should be observed:
1. Inspect the glass regularly for cracks and breaks. If you
detect a crack or break, extinguish the fire immediately,
and contact your dealer for replacement.
2. Do not slam door or otherwise impact the glass. When
closing doors, make sure that logs or other objects do
not protrude to impact the glass.
3. Do not clean the glass with materials which may scratch
(or otherwise damage) the glass. Scratches on the
glass can develop into cracks or breaks.
4. Never attempt to clean the glass while unit is hot. Light
deposits are normal. Heavier deposits may be removed
with the use of a readily available oven cleaner.
5. Never put substances which can ignite explosively in
the unit since even small explosions in confined areas
can blow out the glass.
6. This unit has an air wash system designed to reduce
deposits on glass.
gASkET REplACEMENT
After extensive use, the gasket material which provides
glass and door seal may need to be replaced if it fails
to sustain its resilience. Inspect glass and door seal
periodically to ensure proper seal: if gaskets become
frayed or worn, replace immediately. Contact your dealer
for approved replacement parts. Refer to replacement parts
list in this manual.
63D4004
NOTE: Wear safety glasses and gloves when performing
any maintenance task.
The following steps should be followed for glass gasket
replacement:
1. Ensure appliance is not in operation and is thoroughly
cooled
2. Remove door and place on a protected flat surface.
3. Remove screws and glass clips.
4. Lift glass out.
5. Remove old gasket and clean or replace glass.
6. Sand gasket groove and wipe clean (rubbing alcohol
works well).
7. Put a thin film of gasket cement on the door.
8. Replace new gasket starting at the top center of the
door.
9. Trim to length and butt ends together. Remove all
excess cement.
ST1088
10.Replace glass in door, being sure not to over-tighten
screws and clips.
dOOR gASkET REplACEMENT
The following steps should be followed for door gasket
replacement:
1. Ensure appliance is not in operation and is thoroughly
cooled.
2. Remove door and place on a protected flat surface.
3. Remove old door gasket and clean channel.
4. Sand gasket groove and wipe clean (rubbing alcohol
works well).
5. Using an approved high temperature gasket cement,
apply a thin coat in bottom of channel.
6. Starting at top center of door, work into channel around
door unit, trim to length and butt ends.
7. Close door and allow three to four hours for cement to
set before restarting appliance.
ASh dISpOSAl
Ashes should be placed in a metal container with a tight-
fitting lid. The closed container of ashes should be placed
on a non-combustible floor or on the ground, well away
from all combustible materials, pending final disposal. If the
ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container
until all cinders have thoroughly cooled. Other waste should
not be placed in the ash container.
ThINgS TO REMEMbER IN CASE OF
ChIMNEY FIRE:
1. ClOSE dRAFT CONTROl
2. CAll ThE FIRE dEpARTMENT
SSI30 Wood Insert
19
Advertisement
Table of Contents
