Summary of Contents for Supermicro Supero SAS-827T
Page 1
R R R R R R R R R R UNLESS OTHERWISE PRIMARY-SIDE SPECIFIED DIMENSIONS ARE IN INCHES PROJECT NAME: SAS827T TOLERANCES DESIGNED BY SUPERMICRO U.S.A. DECIMAL ANGLE www.supermicro.com DATE: 01/19/2009 REV: 1.01 MACH FINISH SAN JOSE,CA 95131 DESINGER: Shen .010 TEL:408-503-8000 FAX:408-503-8008 SAS-827T Backplane USER'S GUIDE Rev. 1.0a...
Page 2
SAS-827T Backplane User’s Guide The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.
Preface Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel:...
SAS-827T Backplane User’s Guide Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be- fore any warranty service will be rendered. You can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried.
ESD Safety Guidelines ................... 1-1 General Safety Guidelines ................1-1 An Important Note to Users ................1-2 Introduction to the SAS-827T Backplane ............1-2 Chapter 2 Connectors, Jumpers and LEDs Front Connectors and Jumpers ..............2-1 Front Connectors .................... 2-1 SAS Ports ......................
• Disconnect the power cable before installing or removing any cables from the SAS-827T backplane. • Make sure that the SAS-827T backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage.
Introduction to the SAS-827T Backplane The SAS-827T backplane has been designed to utilize the most up-to-date technol- ogy available, providing your system with reliable, high-quality performance. This manual reflects SAS-827T Revision 1.01, the most current release available at the time of publication.
Page 12
SAS-827T Backplane User's Guide 13. Backplane Main Power Connectors Backplane Main Power The 4-pin connector, designated JP48, pro- 4-Pin Connector vides power to the backplane. See the table Pin# Definition on the right for pin definitions. +12V 2 and 3...
Page 13
Chapter 2: Connectors, Jumpers and LEDs 22. - 33. SAS Ports The SAS-827T backplane is designed with four separate sectors, which support from one to four motherboards independently of each other. The SAS ports are used to connect the SAS drive cables. The 12 ports are designated A0, A1, A2, B0, B1, B2, C0, C1, C2 and D0, D1, D2.
SAS-827T Backplane User's Guide Rear Connectors and LED Indicators R177 SAS D2 SAS C2 R182 R174 SAS A2 SAS B2 R178 R173 SAS C1 SAS D1 R165 SAS B2 SAS A1 R148 R164 SAS827T SAS D0 SAS B0 SAS C0 R179 REV 1.01...
Page 17
Chapter 2: Connectors, Jumpers and LEDs Notes...
Page 18
SAS-827T Backplane User's Guide Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per- form be reasonably expected to result in significant injury or loss of life or catastrophic property damage.
Need help?
Do you have a question about the Supero SAS-827T and is the answer not in the manual?
Questions and answers