Table of Contents
Advertisement
Preset tuning
Presetting stations
Auto presetting
n
1 Tune to the frequency where you want to
begin presetting. (á page 38)
Set the channel reception to FM 87.50 MHz or AM 522 kHz
(9 kHz steps), AM 530 kHz (10 kHz steps) if you want automatic
presetting to start from the lowest frequency.
Preset channels that are automatically assigned by this unit
are:
FM: 1 to 30
AM: 21 to 30
Preset the FM stations first. If the AM stations are preset
before the FM stations, they will be erased when the FM
stations are preset.
MENU/
SETUP
-
-
2 Press
to enter the MENU.
RETURN
3 Select "TUNER " and confirm the setting.
4 Select "AUTO MEMO " and confirm the setting.
5 Select "START " and press [ENTER].
Select "CANCEL " to cancel.
• During automatic presetting, the memory indicator (
and the frequency scrolls. The memory indicator and channel
number are displayed for a second when a station is preset.
• The last station to be preset is displayed when presetting finishes.
• Frequencies may not be preset correctly when broadcast waves are
too strong or too weak. In such cases, carry out presetting manually.
Listening to preset stations
(Using the remote control)
Select the channel.
n
• Hold down the button to change
Press
CH
Press the numbered buttons to select the channel.
n
Press
To select a two digit number
0
-/- -
Reducing excessive noise
Select if noise is excessive during radio reception.
Press [-MENU/–SETUP, RETURN] to enter the MENU.
During FM stereo reception
n
You can improve FM reception by switching reception to
monaural.
1 Select "TUNER " and confirm the setting.
2 Select "FM MODE " and confirm the setting.
3 Select "MONO " and confirm the setting.
• When this is set, "MONO" appears on the display.
• Select "AUTO " to cancel.
4 Press [-MENU/–SETUP, RETURN] twice to
select "EXIT " and press [ENTER].
) flashes
M
channels faster.
e.g. 21: [ ≧10, -/--] → [2] → [1]
Manual presetting
n
1 Tune to the station you want to preset.
(á page 38)
MENU/
SETUP
-
-
2 Press
to enter the MENU.
RETURN
3 Select "TUNER " and confirm the setting.
4 Select "MEMORY " and confirm the setting.
5 Select a channel number and press [ENTER].
"STORED " is displayed.
• To continue presetting, press [TUNE 2 or 1] to tune
another station from step 1.
6 Press [-MENU/–SETUP, RETURN] twice to
select "EXIT " and press [ENTER].
• FM stations can also be preset in the MONO mode
(below).
(Using the unit)
MENU/
SETUP
-
-
1 Press
to enter the MENU.
RETURN
2 Select "TUNER " and confirm the setting.
3 Select "TUNE MODE " and confirm the setting.
4 Select "PRESET " and confirm the setting.
5 Press [-MENU/–SETUP, RETURN] twice to
select "EXIT " and press [ENTER].
TUNE
6 Press
to select the channel.
• Hold down the button to change channels faster.
• Select "MANUAL " in step 4 when you wish to perform manual
tuning (á page 38).
During AM reception
n
When there is a lot of noise interference with an AM broadcast,
try switching to this mode.
1 Select "TUNER " and confirm the setting.
2 Select "BEAT PROOF " and confirm the setting.
3 Select "MODE 1 " or "MODE 2 " and confirm
the setting.
Factory setting: MODE 1
4 Press [-MENU/–SETUP, RETURN] twice to
select "EXIT " and press [ENTER].
39
RQT8743
Advertisement
Table of Contents
