Table of Contents
Advertisement
Enjoying the Home Theater
INPUT SELECTOR
1
To turn the unit on
Press
The "SURROUND" indicator lights on (factory
setting).
To select "SPEAKERS A"
2
Press
To use bi-wire speakers (á page 20)
Press [SPEAKERS A] or [SPEAKERS B] to switch
"
A
B
To switch input sources
3
• Select the connected terminal when the names of the
terminal and equipment you wish to use for playback
do not match.
Turn
To use a DVD recorder with built-in VCR (á page 17)
• To play a DVD: select "DVR "
• To play a video cassette: select "VCR "
Play the selected input source.
4
To adjust the volume
5
Turn
To finish the Home Theater
Be sure to reduce the volume and press [8] to turn the unit to standby.
Digital signals this unit can play:
Dolby Digital (including Dolby Digital Surround EX), DTS (including DTS-ES and DTS 96/24) and PCM (á page 37)
Note
• The unit memorizes whether [SURROUND] has been pressed
on or off for each input source.
• The setting always switches from off to on when the input comes
from a surround source in Dolby Digital, DTS or other formats.
• When you press [SURROUND] off while playing a surround
source (excluding a DVD-Audio source that does not allow
down-mixing), 2-channel mix (2CH MIX) activates.
2-channel mix is cancelled when you turn the unit off or when
you switch input sources.
• The "SURROUND" indicator goes off when the sampling
24
frequency for the input signal is higher than 96 kHz.
RQT8743
"SURROUND"
" "
"BI-AMP"
INPUT SELECTOR
BI-AMP
SURROUND
ADVANCED DUAL AMP
TUNE
-MENU/-SETUP ENTER
SURROUND
SPEAKERS
RETURN
AUTO DETECTOR
-
MENU/
-
SETUP
ENTER
SURROUND
SPEAKERS
TUNE
RETURN
AUTO DETECTOR
"ADVANCED DUAL AMP"
8
SPEAKERS
to switch "
" on.
A
A
" on.
INPUT SELECTOR
VOLUME
SPEAKERS
A
B
VOLUME
VOLUME
AUTO SPEAKER SETUP
HDMI
SETUP MIC
AUX
S VIDEO
VIDEO
L
-
AUDIO
-
R
SETUP MIC
AUX
SURROUND
• The standby indicator "^" goes off when you turn the unit on.
Note
Do not forget to perform speaker detection when you play
a source with the unit for the first time or when you change
the number of connected speakers (á pages 10 and 22).
SPEAKERS
A
SPEAKERS
BI-WIRE
A
B
(e.g.)
TUNER FM
TUNER AM
AUX
VCR
• When you select "DVR ", "DVD RECORDER " scrolls across
the display once.
• You can also select an input source using the remote control (
Volume range:
– – dB (minimum),
–79dB to 0dB (maximum)
• The number of source channels appears on the display when
a digital signal is input or input sources are switched. (Their
number may not appear depending on the selected source.)
• The unit is compatible with linear PCM 8-channel surround
signals decoded by the BD player and other equipment (up to
96 kHz/24 bit). See the operating instructions for equipment
used for playback.
RECEIVER
AV
SYSTEM
RECORDER
TV
DVD
TUNER
PLAYER
CD
VCR
BD/DVD
BAND
ANALOG 6CH
CH
To select "SPEAKERS B"
Press [SPEAKERS B].
(
page 25)
á
To enjoy BI-AMP stereo sounds
See page 25.
CD
TV/STB
DVR
BD/DVD
á
To switch between 2-channel
stereo playback and surround
playback
Press [SURROUND].
Subwoofer
Number of surround and surround back channels
Number of front and center channels
page 5).
Advertisement
Table of Contents
