Introduction Welcome to Belkin Hi-Speed Connectivity! Thank you for purchasing the Belkin Hi-Speed USB 2.0 Notebook Card (the Notebook Card). Now you can upgrade your computer to the latest USB technology. You will be able to take advantage of a host of new Hi-Speed USB 2.0 products! Connecting your USB 2.0 devices to your computer through the newest USB...
Overview Features • 2 Hi-Speed USB 2.0 ports • Simultaneous connection capability for low-speed, full-speed, and high- speed devices • Auto-detection of new devices as they are connected, along with the speed of each device • Backward-compatibility with USB 1.1 devices •...
Overview Package Contents • User Manual • I nstallation CD • Power Supply System Requirements • 266MHz Pentium ® • 32MB RAM • PC-compatible laptop computer with available 32-bit Type II CardBus slot • Windows 98 SE, 2000, Me, or XP operating system ®...
Operating System Compatibility Operating System USB 1.x Support USB 2.0 Support Windows 98 SE Windows 2000 Windows Me Windows XP Please refer to the section that corresponds to your version of the Windows operating system. Note: The included power supply is not needed for bus-powered USB devices such as USB keyboards that do not include a built-in USB hub, mice, or self- powered USB devices such as certain hard drives, printers, etc.
Installation Installation Procedure for Windows 98 SE This installation procedure will install two USB 1.1 OHCI controllers, one USB 2.0 EHCI host controller, and the associated USB root hubs. Note: Do not insert the Notebook Card into your computer until instructed to do so.
Page 8
11. The “Add New Hardware” wizard will repeat the installation process for the second OHCI host controller. 12. Repeat steps 7-10. 13. Windows will now detect “Belkin USB 2.0 High Speed Host Controller”. Click “Next”. 14. Windows will locate the required drivers and complete installation of the “Belkin USB 2.0 High Speed Host Controller”...
1. Right-click on “My Computer” and select “Properties”. 2. Select the “Device Manager” tab. 3. After installation of the Belkin USB 2.0 driver you will notice that an additional “Universal Serial Bus Controllers” heading has been added to the device list.
6. Insert the Notebook Card into the slot. Apply pressure as needed until it is fully seated. 7. After the Notebook Card is inserted, Windows will detect “NEC USB Open Host Controller (E13+)” and “Belkin USB 2.0 Hi-Speed Host Controller”. The required driver support will be automatically installed. No user input is required.
1. Right-click on “My Computer” and select “Properties”. 2. Select the “Device Manager” tab. 3. After installation of the Belkin USB 2.0 driver, you will notice that an additional “Universal Serial Bus Controllers” heading has been added to the device list.
Please proceed to the “Installing the Microsoft Driver” section. 2. If you do not have an Internet connection: USB 2.0 drivers will be installed from the Belkin Driver Installation CD. Please proceed to the “Installing the Belkin Driver” section. Installing the Microsoft Driver 1.
Note: If the “Microsoft Windows Update” option is not available, double-check your connection to the Internet. If you are having problems connecting to the Internet, proceed to the “Installing the Belkin Driver” section. 8. The driver for “Universal Serial Bus Controller” will be located. Click “Next”.
Note: If your computer features built-in USB ports, or if you have other USB PCI controller cards installed, you will see additional USB controller and root hub entries in the Device Manager list. Installing the Belkin Driver Note: Do not insert the Notebook Card into your computer until instructed to do so.
After the installation is complete, you may be prompted to click “Finish” and to restart your computer. Verifying Proper Installation (Belkin Driver) After installation is complete, check the Windows Device Manager to confirm that all components of the Notebook Card have been properly installed.
Page 16
Installation 4. After installation of the Belkin USB 2.0 driver, you will notice that a second “Universal Serial Bus Controllers” heading has been added to the device list. a) Click the plus sign (+) next to the original “Universal Serial Bus Controllers”...
Notebook Card is already installed on your computer. If you have not upgraded to Windows XP Service Pack 1, or if you wish to use the Belkin driver, proceed to the “Installing Belkin Driver” section. Using the Windows XP Service Pack 1 Driver This installation procedure will install two USB 1.1 OHCI controllers and one...
Page 18
Note: If your computer features built-in USB ports, or if you have other USB PCI controller cards installed, you will see additional USB controller and root hub entries in the Device Manager list. Installing the Belkin Driver Note: Do not insert the Notebook Card into your computer until instructed to do so.
2. Select “Properties”. 3. Select the “Hardware” tab and click on the “Device Manager” button. 4. After installation of the Belkin USB 2.0 driver, you will notice that a second “Universal Serial Bus Controllers” heading has been added to the device list.
Installation Note: If your computer features built-in USB ports, or if you have other USB PCI controller cards installed, you will see additional USB controller and root hub entries in the Device Manager list. The installation procedure is now complete. Installing a Hi-Speed USB 2.0 Hub Note: During installation of the Hi-Speed USB 2.0 Notebook Card driver, a Hi-Speed USB 2.0 hub driver is also installed.
Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product.