Related Manuals for Yamaha FX High Output WaveRunner 2007
Summary of Contents for Yamaha FX High Output WaveRunner 2007
- Page 1 2007 WaveRunner FX High Output FX Cruiser High Output OWNER’S/OPERATOR’S MANUAL U.S.A. Edition LIT-18626-06-87 READ THIS MANUAL CAREFULLY BEFORE OPERATION! F1X-F8199-11...
- Page 3 Important manual information EJU30180 To the owner/operator NOTE: A NOTE provides key information to make Thank you for choosing a Yamaha watercraft. procedures easier or clearer. This owner’s/operator’s manual contains in- formation you will need for proper operation, EJU30220 maintenance, and care. A thorough under-...
-
Page 4: Table Of Contents
Star labels ......... 2 Yamaha Engine Management Important labels ......4 System (YEMS) ......38 Warning labels ........5 Yamaha Security System and Other labels ........7 low-RPM mode ......38 Multifunction information center ..40 Safety information......9 Storage compartments ....50 Limitations on who may operate the watercraft ...... - Page 5 Docking the watercraft ..... 77 Consumer information ....103 Reverse on waterways ....77 Limited warranty ......103 Rough water operation ....78 YAMAHA EXTENDED SERVICE Post-operation care ...... 78 (Y.E.S.) ........105 Transporting ......... 79 Maintenance and care..... 80 Storage .........
-
Page 6: General And Important Labels
Hull Identification Number (HIN), and engine serial number in the spaces provided for assistance when ordering spare parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen. -
Page 7: Emission Control Information
General and important labels EJU30350 EJU30430 Emission control information Manufactured date label This label is attached to the top of the cylinder This engine conforms to 2007 U.S. Environ- head. mental Protection Agency (EPA) and/or Cali- fornia Resources Board (CARB) regulations for marine SI engines. - Page 8 General and important labels One Star - Low Emission exhaust emission standards or the Sterndrive The one-star label identifies engines that and Inboard marine engine 2003-2008 ex- meet the Air Resources Board’s Personal haust emission standards. Engines meeting Watercraft and Outboard marine engine 2001 these standards have 65% lower emissions exhaust emission standards.
-
Page 9: Important Labels
General and important labels EJU30450 Important labels... -
Page 10: Warning Labels
General and important labels EJU35910 Warning labels... - Page 11 General and important labels...
-
Page 12: Other Labels
General and important labels EJU35922 Other labels... - Page 13 General and important labels The following label indicates the correct direction to upright a capsized watercraft.
-
Page 14: Safety Information
The safe use and operation of this water- operate the watercraft craft is dependent upon the use of proper Yamaha recommends a minimum operator riding techniques, as well as upon the age of 16 years old. common sense, good judgment, and ex- Adults must supervise use by minors. -
Page 15: Cruising Limitations
Safety information teristics of the watercraft before trying any EJU30760 Cruising limitations difficult maneuvers. Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. Operate defensively at safe speeds and keep a safe distance away from people, ob- jects, and other watercraft. - Page 16 Safety information kles, and other bones. Do not jump wakes with another boat, which could result in se- or waves. vere injury or death. Do not operate the watercraft in rough wa- ter, bad weather, or when visibility is poor; this may lead to an accident causing injury or death.
-
Page 17: Operation Requirements
Safety information know that a helmet could help protect you in EJU30811 Operation requirements certain kinds of accidents and that it could All riders must wear a U.S. Coast Guard injure you in others. (USCG) approved personal flotation device A helmet is designed to provide some head (PFD) that is suitable for personal water- protection. - Page 18 Safety information NEVER operate the watercraft after con- Always consult your doctor on whether it is suming alcohol or taking other drugs. safe for you to ride this watercraft if you are pregnant or in poor health. Do not attempt to modify this watercraft! Modifications to your watercraft may reduce safety and reliability, and render the water- craft unsafe or illegal for use.
-
Page 19: Recommended Equipment
A mirror can also be used as an emergency signal. Contact a Yamaha dealer or the U.S. Coast Guard for more information. Watch A watch is helpful so you will know how long you have been operating the watercraft. -
Page 20: Hazard Information
Always operate the watercraft in an This model is equipped with the Yamaha open area. Engine Management System (YEMS) that Do not touch the hot oil tank, muffler, or en-... - Page 21 Safety information Reverse can be used to slow down or stop any debris or weeds, which may have col- during slow-speed maneuvering, such as lected around the jet intake. when docking. Once the engine is idling, shift into reverse and gradually increase en- gine speed.
-
Page 22: Water-Skiing
Safety information is required by law. Let the skier direct the EJU30940 Water-skiing operator’s control of speed and direction You can use the watercraft for water-skiing if with hand signals. it has the seating capacity to carry the opera- The spotter should sit astride the rear of the tor, a rearward-facing spotter, and the water- seat and hold onto the handgrip with both skier when he or she is not skiing. - Page 23 Safety information watch the skier’s hand signals and condi- until the watercraft is well away from the ski- tion. er and slack in the ski rope is taken up. Make sure that the rope is not looped around anything. After checking that the skier is ready and that there is no traffic or other obstacles, ap- ply enough throttle to raise the skier.
-
Page 24: Rules Of The Road
EJU30960 Rules of the Road The vessel which does not have the right-of- Your Yamaha watercraft is legally consid- way has the duty to take positive and timely ered a powerboat. Operation of the water- action to stay out of the way of the stand-on craft must be in accordance with the rules vessel. - Page 25 Safety information give-way vessels). Both you and the meeting provided the other vessel gives you the right- vessel must alter course to avoid each other. of-way as it should. Meeting Overtaking If you are meeting another power-driven ves- If you are passing another vessel, you are the sel head on, and are close enough to run the give-way vessel.
- Page 26 Safety information Fishing vessel right-of-way Many bodies of water used by boaters are en- All vessels fishing with nets, lines, or trawls tirely within the boundaries of a particular are considered to be “fishing vessels” under state. The Uniform State Waterway Marking the International Rules.
- Page 27 Safety information They signify speed zones, restricted areas, danger areas, and general information. Remember, markings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters.
-
Page 28: To Get More Boating Safety Information
Power Squadron. Watercraft Education and Training The Online Boating Safety Course, available through the watercraft section of the yamaha- motor.com website, is a free, 50 question learning course available to the public. Upon successful completion of 80 percent or better,... -
Page 29: Enjoy Your Watercraft Responsibly
Safety information EJU30990 Enjoy your watercraft responsibly You share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, wa- ters, and wildlife with respect and courtesy. Whenever and wherever you ride, think of yourself as the guest of those around you. -
Page 30: Features And Functions
Features and functions EJU31010 Location of main components Front view 1 Handlebars 2 Rear seat 3 Front seat 4 Footwell 5 Sponsons 6 Gunwale 7 Pull-up cleat (for FX Cruiser High Output) 8 Cooling water pilot outlet 9 Bow eye 10 Hood... - Page 31 Features and functions Rear view 1 Fuel tank filler cap 2 Intake grate 3 Speed sensor 4 Stern eyes 5 Stern drain plugs 6 Reverse gate 7 Ride plate 8 Jet thrust nozzle 9 Reboarding step 10 Electric bilge pilot outlet 11 Cleat 12 Handgrip...
- Page 32 Features and functions Control system 1 Multifunction information center 2 Beverage holder 3 Rearview mirrors 4 Throttle lever 5 Shift lever 6 Tilt lever 7 Glove compartment 8 Engine stop switch 9 Engine shut-off cord (lanyard) 10 Quick Shift Trim System (QSTS) selector 11 QSTS selector lock lever 12 Watertight compartment 13 Remote control transmitter...
- Page 33 Features and functions Engine compartment 1 Air filter case 2 Water separator 3 Fuel tank 4 Battery 5 Flushing hose connector 6 Electrical box 7 Oil tank 8 Muffler 9 Spark plugs/Spark plug caps/Ignition coils 10 Spark plug lead...
-
Page 34: Operation Of Controls And Other Functions
Features and functions EJU31020 To install the rear seat: Operation of controls and other Insert the projections on the front of the seat functions into the stays on the deck, and then push the EJU31040 rear of the seat down to lock it in place. Seats To remove the rear seat: Pull the rear seat latch up, and then pull the... -
Page 35: Hood
Features and functions To install the front seat: EJU31061 Hood (1) Insert the projections on the front of the To open the hood, push the hood latch down, seat into the stays on the deck, and then and then lift up the hood. push the rear of the seat down to lock it in place. -
Page 36: Fuel Tank Filler Cap
If the remote control transmitter needs a mitter.) new battery or is not operating properly, contact a Yamaha dealer. Do not attempt to replace the battery yourself. ECJ00750 CAUTION: The Yamaha Security System and low-... -
Page 37: Engine Stop Switch
Features and functions switch, such as if the operator falls off the wa- NOTE: tercraft. While the engine is running, input from the re- mote control transmitter is not received. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including in-... -
Page 38: Start Switch
The engine will not start when the lock mode To check for proper operation of the cooling of the Yamaha Security System has been se- system, check that water is being discharged lected, the clip is removed from the engine from the port (left) pilot outlet. -
Page 39: Steering System
This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. -
Page 40: Shift Lever
Features and functions otherwise the handlebars may suddenly Do not touch the reverse gate while the change position, which may lead to an shift lever is being operated, otherwise accident. you could be pinched. To shift into forward: EJU31300 Shift lever (1) Release the throttle lever and let the en- The shift lever is located on the starboard gine speed return to idle. - Page 41 Features and functions There are 5 positions: 2 bow-down positions To enhance particular types of performance, (a) and (b), neutral “N”, and 2 bow-up posi- select bow down or bow up. tions (c) and (d). EJU31330 Bow down To change the trim angle: Turn the QSTS selector to (a) or (b) and the (1) Reduce engine speed to 4000 r/min or bow will go down while the watercraft is on...
-
Page 42: Handgrip
Features and functions ahead acceleration when on plane and top EJU34860 Reboarding step speed are enhanced. The reboarding step provides a handhold and In some conditions, however, the watercraft footstep for boarding the watercraft. may tend to “porpoise” (hop in the water). If the watercraft is porpoising, select neutral or bow down. -
Page 43: Stern Eyes
If you lose the EJU34890 remote control transmitter or it does not oper- Pull-up cleats (for FX Cruiser High ate properly, contact a Yamaha dealer. Output) The pull-up cleats are used to attach a rope to the watercraft when mooring it. - Page 44 This indicates the lock mode is selected and the engine cannot be started. 1 Unlock button Engine 1 Lock button Number Yamaha Security Sys- can be of beeps tem mode started The “UNLOCK” indicator light comes on when 1 beep...
-
Page 45: Multifunction Information Center
The multifunction information center will continue to operate for 25 seconds after the ECJ00080 engine stops. CAUTION: If the remote control transmitter does not operate when its buttons are pressed, the battery may be low. Have a Yamaha dealer replace the battery. - Page 46 Features and functions EJU34930 “RPM” indicator light comes on when the an- Analog speedometer/tachometer and indi- alog tachometer is selected. cator lights This watercraft is equipped with the following meter and indicator lights. 1 “Speed/RPM” button 2 “SPEED” indicator light 3 “RPM”...
- Page 47 The analog speedometer/tachometer is The “UNLOCK” indicator light comes on when switched to the speedometer function. the unlock mode of the Yamaha Security Sys- The display units of the multifunction meter tem is selected. The watercraft can be ridden are switched to miles from kilometers.
- Page 48 Features and functions EJU35010 The following operation buttons are on the left “L-MODE” indicator light side of the multifunction meter. The “L-MODE” indicator light comes on when the low-RPM mode is selected. (See page 39 for more information.) 1 “Speed/RPM” button 2 “Volt/Hour”...
- Page 49 Features and functions operating, or if the display units of the meter The fuel level meter has eight segments are switched to miles. which show the amount of fuel remaining in the fuel tank. 1 “Volt/Hour” button 1 Fuel level meter NOTE: The fuel level is most accurate when the wa- tercraft is sitting level on a trailer or in the wa-...
- Page 50 If the oil level is low, add enough starts sounding intermittently. engine oil to raise it to the proper level. If the oil level is sufficient, have a Yamaha dealer check the watercraft. NOTE: Press any button on the multifunction meter to stop the buzzer.
- Page 51 ECJ00040 CAUTION: If you cannot locate and correct the cause of the overheating, consult a Yamaha deal- er. Continuing to operate at higher speeds could result in severe engine damage. NOTE: EWJ00050...
- Page 52 1 “Mode/Reset” button If this occurs, reduce the engine speed, return 2 “Start/Stop” button to shore, and have a Yamaha dealer check To switch the display mode, push the the engine. “Mode/Reset” button for less than 1 second.
- Page 53 Features and functions the display units of the meter are switched Average speed This display shows the average speed in to miles/gallons/degrees Fahrenheit. miles per hour “AV MPH” or kilometers per hour “AV KMH” since it was reset. 1 “Volt/Hour” button 2 “SPEED”...
- Page 54 Features and functions Fuel consumption per hour Water temperature This display shows the current fuel consump- This display shows the ambient water temper- tion in gallons per hour “G/HR” or liters per ature “L TEMP” (lake temperature). hour “L/HR”. Air temperature This display shows the ambient air tempera- Fuel consumption per kilometer/mile This display shows the current fuel consump-...
-
Page 55: Storage Compartments
Features and functions surements are stopped. The beeper sounds EJU35151 Front storage compartment twice. The front storage compartment is located at the bow. To open the front storage compartment, push the hood latch down, and then lift up the hood. 1 “Mode/Reset”... - Page 56 Features and functions To open the glove compartment, turn the Front storage compartment: glove compartment knob, and then lift up the Capacity: 75.0 L (19.8 US gal) (16.5 Imp.gal) lid. Load limit: 5.0 kg (11 lb) To close the front storage compartment, push down on the rear of the hood until it latches securely.
- Page 57 Features and functions To open the seat storage compartment, re- EJU35170 Beverage holder move the rear seat. (See page 29 for rear seat The beverage holder is located on the star- removal and installation procedures.) board (right) side of the watercraft. 1 Beverage holder NOTE: Do not place beverages in the beverage hold-...
- Page 58 Features and functions NOTE: Make sure that the watertight compartment cap is closed securely before operating the watercraft.
-
Page 59: Operation
Gasohol containing methanol is not recom- dry rags. Always properly dispose of mended by Yamaha because it can cause gasoline-soaked rags. fuel system damage and engine performance Avoid overfilling the fuel tank. Stop fill- problems. -
Page 60: Engine Oil
Operation EJU31890 ly 50 mm (2 in) from the top of the fuel Engine oil tank as indicated in the illustration. Use a combination of the recommended SAE and API engine oil classifications shown in the chart below. ECJ00280 CAUTION: Use only 4-stroke engine oil. -
Page 61: Pre-Operation Checks
Operation EJU31980 Pre-operation checks EJU31990 Pre-operation check list Before operating this watercraft, perform the checks in the following check list. See the accom- panying text in this chapter for details on how to perform the checks. EWJ00410 WARNING If any item in the pre-operation check list is not working properly, have it inspected and repaired before operating the watercraft, otherwise an accident could occur. - Page 62 Operation NOTE: Pre-operation checks should be made each time the watercraft is used. These checks can be completed in a short time. It is worth the time spent to ensure safety and reliability.
-
Page 63: Pre-Operation Check Points
Check the hull and deck for cracks and other enter the oil tank filler hole. Debris and damage. If any damage is found, have a water in the engine oil can cause serious Yamaha dealer repair the watercraft. engine damage. EJU32380 Fuel level... - Page 64 If the ambient temperature is 20 °C (68 °F) or mum level mark, the oil tank is overfilled. less, warm up the engine for an additional 5 Have a Yamaha dealer remove the ex- minutes. cessive amount of engine oil.
- Page 65 Operation the water is discharged from the electric bilge could be damaged, allowing water to en- pilot outlet at the stern. ter the engine compartment. Make sure that the stern drain plugs are tightened securely before launching the watercraft. Otherwise, water may flood the engine compartment and cause the watercraft to submerge.
- Page 66 Operation Check that the battery leads are tightened se- EJU32570 Fire extinguisher curely and that there is no corrosion on the Check that there is a full fire extinguisher on battery terminals. board. 1 Positive (+) battery terminal: Red lead The fire extinguisher container is located in 2 Negative (–) battery terminal: Black lead the seat storage compartment.
- Page 67 Operation contact a Yamaha dealer or a fire extin- turned, and that there is no free play between guisher dealer to obtain one meeting the the handlebars and the jet thrust nozzle. proper specifications. Fire extinguisher: Classification: Capacity: 2 lb or more...
- Page 68 Operation Also, make sure that the reverse gate goes up EJU32641 Quick Shift Trim System (QSTS) completely when the shift lever is pushed Operate the QSTS selector lock lever and the down. QSTS selector several times to check that they operate properly. (1) Squeeze the QSTS selector lock lever and check that it returns smoothly to its original position when released.
- Page 69 If the mechanism does not work properly, have a Yamaha dealer service it. EJU32650 Jet intake Carefully check the jet intake for weeds, de- bris, or anything else that might restrict the in- take of water.
- Page 70 Operation EJU32670 is running and the watercraft is in the water. Switches (See page 33 for more information.) ECJ00410 CAUTION: Do not run the engine for more than 15 seconds when checking the switches on land without supplying water, otherwise the engine could overheat.
-
Page 71: Operation
When launching the watercraft, make sure that there are no obstacles behind you. Use the remote control transmitter to select the unlock mode. (See page 38 for Yamaha Security System and low-RPM mode selec- tion procedures.) After the watercraft is in the water, start the engine. - Page 72 Operation (1) If the lock mode of the Yamaha Security (3) Attach the engine shut-off cord to your left System is selected, use the remote con- wrist, and then attach the clip to the en- trol transmitter to select the unlock mode.
-
Page 73: Stopping The Engine
If the engine does not start of accidental starting or unauthorized use by in 5 seconds, release the start switch, children or others. (See page 38 for Yamaha wait 15 seconds, and then try again. Security System and low-RPM mode selec-... -
Page 74: Operating Your Watercraft
Operation EJU32900 Check state and local laws before operating Operating your watercraft your watercraft. EJU32951 Operate defensively at safe speeds and keep Getting to know your watercraft a safe distance away from people, objects, Operating your watercraft requires skills ac- and other watercraft. -
Page 75: Riding With Passengers
Operation fabrics, like those used in bicycle shorts. A full vided, and keep their feet on the floor of the wetsuit can also protect against hypothermia footwell. Never allow a passenger to ride in (subnormal body temperature) and abra- front of the operator. sions. -
Page 76: Boarding And Starting In Deep Water
Operation Practice reboarding in shallow water be- (2) Board the watercraft from the side or the fore riding in deep water. rear. (3) Attach the engine shut-off cord to your left wrist, and then attach the clip to the en- gine shut-off switch. - Page 77 Operation EJU35230 start the engine, and then look in all direc- Boarding alone tions before starting off. (1) Swim to the rear of the watercraft and place both hands on the boarding plat- form, pull yourself up, and then grasp the handgrip with one hand.
- Page 78 Operation (1) Climb on board as noted in the previous NOTE: section, and sit astride the seat. When a passenger is boarding, both the pas- sengers and the operator should try to bal- ance the watercraft. (5) Check that the passengers have their feet on the floor of the footwell and are securely holding on to the person in front of them or to the handgrip provided.
-
Page 79: Capsized Watercraft
Operation tion, and then move to the seat and sit (6) Gradually increase the speed to balance astride to balance the watercraft. the watercraft. (2) Have a passenger pull him or herself up onto the boarding platform into a kneeling position, then move to the seat and sit astride to balance the watercraft. -
Page 80: Turning The Watercraft
Operation ride plate while pushing down on the gun- ECJ00550 CAUTION: wale with your right hand or foot. Do not operate the engine at full throttle for at least 1 minute after the engine has been restarted. Excessive water in the bilge can splash into the engine, which can result in severe damage. - Page 81 This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever (see condition C above).
-
Page 82: Stopping The Watercraft
Operation put until you apply throttle again or you reach steer away from a boat or other obstacle trolling speed. that comes into your path. EJU33290 Do not use the reverse function to slow Stopping the watercraft down or stop the watercraft as it could The watercraft is not equipped with a sepa- cause you to lose control, be ejected, or rate braking system. -
Page 83: Rough Water Operation
Operation Once the engine is idling, shift into reverse EJU33390 Post-operation care and gradually increase engine speed. Make To keep your watercraft in top shape, always sure that there are no obstacles or people be- take it out of the water after using it and per- hind you before shifting into reverse. -
Page 84: Transporting
Before putting the watercraft on the trail- (11) Spray a rust inhibitor, such as Yamaha er or transporting it, be sure to put the Silicone Protectant and Lubricant, on me- shift lever in the forward position, other- tallic parts to minimize corrosion. -
Page 85: Maintenance And Care
It is advisable 1 Flushing hose connector cap to have the watercraft serviced by a Yamaha 2 Garden hose adapter dealer prior to storage. However, the following 3 Flushing hose connector procedures can be performed by the owner. -
Page 86: Lubrication
EWJ00280 WARNING moval and installation procedures.) GASOLINE AND ITS VAPORS ARE HIGH- (3) Spray a rust inhibitor such as Yamaha LY FLAMMABLE AND EXPLOSIVE! Stor-Rite Engine Fogging Oil into each in- Do not smoke when refueling, and keep take opening for 3 seconds. -
Page 87: Battery
1.28 at 20 °C (68 °F) line in your eyes, get immediate medical attention. It is recommended to have a Yamaha dealer If any gasoline spills on your skin or check the specific gravity and charge the bat- clothing, immediately wash the affected tery. -
Page 88: Maintenance And Adjustments
EJU33800 See a Yamaha dealer for genuine Yamaha re- Owner’s/operator’s manual and tool placement parts and optional accessories de- signed for your watercraft. It is advisable to always carry the owner’s/op- Remember, failures that are the result of the erator’s manual and tool kit with you whenev-... - Page 89 Maintenance and care pairs. The tools provided in the tool kit are suf- ficient for this purpose, except that a torque wrench may also be necessary to tighten nuts and bolts. 1 Tool bag 2 Screwdriver 3 16 mm box wrench 4 10/12 mm box wrench 5 Pliers 6 Open-end wrench...
-
Page 90: Periodic Maintenance Chart
This “ ” mark indicates maintenance that you may do yourself. This “ ” mark indicates work to be done by a Yamaha dealer. Initial Thereafter every Item... - Page 91 Maintenance and care Initial Thereafter every Item Operation hours hours hours hours hours Page months months months months Nuts and bolts Check — Air filter element Check Engine oil Replace Oil filter Replace Valve clearance Check, adjust — * This operation should be performed after every use.
-
Page 92: Checking The Fuel System
Fuel tank filler cap and seal for damage. year or every 100 hours of operation. Fuel in fuel tank for water and dirt. Have a Yamaha dealer replace the oil fil- Fuel tank for damage, cracks, and leakage. ter if necessary. -
Page 93: Checking The Air Filter Element
If oil is leaking or the oil pressure warning indicator comes on when the engine is running, immediately shut the engine off and have a Yamaha dealer check the wa- tercraft. Continuing to operate the engine under such conditions could cause severe engine damage. -
Page 94: Checking The Jet Thrust Nozzle Angle
Maximum 5 mm (0.20 in) 1 Stopper 2 Shift arm If the reverse gate does not reach the correct positions, have a Yamaha dealer service it. EJU34360 Checking and adjusting the throttle cable Check that the throttle cable moves back to the set position smoothly and that the throttle lever free play is within specification. -
Page 95: Cleaning And Adjusting The Spark Plugs
Do not at- tempt to diagnose any problems yourself. Have a Yamaha dealer service the watercraft. Remove and inspect the spark plugs periodi- cally; heat and deposits will cause the spark 1 Spark plug gap plugs to slowly break down and erode. -
Page 96: Lubrication Points
To keep moving parts sliding or rotating smoothly, coat them with water-resistant Steering cable (handlebar end) grease. Recommended water-resistant grease: Yamaha Marine Grease/Yamaha Grease A Throttle cable (throttle body end) Throttle bodies (throttle cable pulley, throt- tle cam, and return spring) -
Page 97: Checking The Battery
Maintenance and care QSTS cables (pulley end) Shift cable (reverse gate end) QSTS cables (handlebar end) Intermediate housing Remove the QSTS cable housing. Spray a Fill the intermediate housing with water-re- rust inhibitor into the outer cables. Reinstall sistant grease through the grease nipple the QSTS cable housing. - Page 98 Battery life could be shortened. trolyte or charging the battery. It is recommended to have a Yamaha dealer charge the battery. If you charge the battery yourself, carefully read the battery charger in- structions before charging and follow the points below.
-
Page 99: Fuel Injection System
EJU34490 Fuel injection system The fuel injection system was set at the Yamaha factory. If the fuel injection system needs to be adjusted, have a Yamaha dealer service the watercraft. ECJ00220 CAUTION: Do not attempt to adjust the fuel injection system. -
Page 100: Specifications
Specifications EJU34542 Spark plug: Specifications CR9EB Watercraft capacity: Spark plug gap: 0.7–0.8 mm (0.028–0.031 in) Maximum people on board: Battery capacity: 3 person 12 V, 19.0 Ah Maximum load capacity: Charging system: 240 kg (530 lb) Flywheel magneto Dimensions: Drive unit: Length: Propulsion system: 3340 mm (131.5 in) -
Page 101: Trouble Recovery
If you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service. EJU34601... - Page 102 Engine runs irregu- Fuel Empty Refill as soon as pos- larly or stalls sible Stale or contaminat- Have serviced by Yamaha dealer Fuel tank Water or dirt present Have serviced by Yamaha dealer Spark plug Fouled or defective Replace Incorrect heat range...
-
Page 103: Emergency Procedures
Trouble recovery EJU34620 contact with the rotating parts of the jet Emergency procedures pump. EJU34630 Cleaning the jet intake and impeller If weeds or debris get caught in the jet intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. -
Page 104: Jumping The Battery
(1) Connect the positive (+) jumper cable to If debris is difficult to remove, consult a the positive (+) battery terminals of both Yamaha dealer. batteries. ECJ00670 (2) Connect one end of the negative (–) CAUTION: jumper cable to the negative (–) battery... -
Page 105: Replacing The Fuses
Trouble recovery gine. Any wrong connection could dam- (2) Replace the blown fuse with the spare age the electrical system. fuse of the correct amperage by using the fuse puller on the reverse side of the cap. (4) Start the engine, and then disconnect the jumper cables by reversing the steps above. -
Page 106: Towing The Watercraft
If the watercraft is submerged or flooded with bars. water, follow the procedure below and consult a Yamaha dealer as soon as possible. Failure ECJ00720 CAUTION: to do so could result in serious engine dam-... - Page 107 Trouble recovery (6) Spray a rust inhibitor such as Yamaha Stor-Rite Engine Fogging Oil into each spark plug hole for 5 seconds. (7) Crank the engine for 5 seconds at wide open throttle. Repeat this step several times. (8) Install the spark plugs, and then connect the spark plug caps and fuel injector cou- plers.
-
Page 108: Consumer Information
Owner’s/Operator’s Manual. The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten [10] days of dis- covery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business. - Page 109 If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new mailing address.
-
Page 110: Yamaha Extended Service (Y.e.s.)
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service. - Page 111 Index Enjoy your watercraft responsibly .... 24 Air filter element, checking ....... 88 Analog speedometer/tachometer ..... 41 Filling the fuel tank ........55 Analog speedometer/tachometer and Fire extinguisher........61 indicator lights........41 Flushing the cooling system ..... 80 Approval label of emission control Front storage compartment ......
- Page 112 (for FX Cruiser Watercraft characteristics......15 High Output) ......... 47 Water-skiing ..........17 Rough water operation......78 Watertight compartment ......52 “RPM” indicator light......... 42 Rules of the Road ........19 Yamaha Engine Management System (YEMS) ..........38...
- Page 113 Index YAMAHA EXTENDED SERVICE (Y.E.S.) ..........105 Yamaha Security System......38 Yamaha Security System and low-RPM mode............. 38 Yamaha Security System lock and unlock modes........38...
- Page 116 YAMAHA MOTOR CORPORATION, USA Printed in USA August 2006–1.7 × 1 CR...