Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZGF 759
Summary of Contents for Zanussi ZGF 759
- Page 1 GAS HOB MODEL ZGF 759 INSTRUCTION BOOKLET...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the appliance. Installation This appliance must be installed by qualified When using other electrical appliances, ensure the personnel, according to the manufacturer ’s cable does not come into contact with the hot instructions and to the rules in force. -
Page 3: Table Of Contents
Contents For the Installer For the User Technical Data Page 9 Description of the Hob Page 5 Installation Page 10 Operation Page 6 Gas Connection Page 10 Maintenance Building In Page 11 and Cleaning Page 7 Fitting the Hob Something to the Worktop Page 12 Not Working... -
Page 4: Description Of The Hob
Description of the Hob Hob Top Auxiliary Burner Semi-rapid Burners Rapid Burner Ignition pushbutton Control knob for front left burner (auxiliary) Control knob for back left buner (semi-rapid) Control knob for central burner (rapid) Control knob for back right burner (semi-rapid) 10. -
Page 5: Operation
Operation This hob is provided with a safety device, which will stop the gas flow if the flame accidentally goes off during cooking. To light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. -
Page 6: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. -
Page 7: Something Not Working
Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check the mains fuse has not blown Check the burner cap and crown have been... -
Page 8: Technical Data
Instructions for the Installer Supply Connections Engineer technical data OVERALL DIMENSIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Width: 680 mm. Depth: 510 mm. Electric: Height: 72 mm. 230-V 50Hz supply, 3 core flexible cable with non Weight: 12 Kg. -
Page 9: Installation
Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/ 2"... -
Page 10: Building In
Building In Building over a cupboard or drawer Building over a kitchen unit with oven If the hob is to be installed above a cupboard or If the hob is built into a kitchen unit with an oven drawer it will be necessary to fit a heat resistant board underneath, the recess must have the dimensions below the base of the hob on the underside of the shown in diagrams 2 and 3, and should also incorpo-... -
Page 11: Fitting The Hob To The Worktop
Fitting the hob to the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, taking care that the seals meet without overlapping;... -
Page 12: Electrical Connection
Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. -
Page 13: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 14: Servicing
Servicing D: Removal Of Burner A: Removal Of Hob Top 1. Follow the procedures in Section A. 1. Remove all control knobs, pan supports, burner caps 2. With the aid a 12mm spanner loosen off the pipe and burner crowns. connection nut.