Related Manuals for Zanussi ZGF 7820
Summary of Contents for Zanussi ZGF 7820
-
Page 1: Gas Hob
GAS HOB ZGF 7820 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance... -
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. -
Page 3: Table Of Contents
Contents For the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? Guarantee/Customer Service European guarantee Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. -
Page 4: Description Of The Hob
Description of the Hob Auxiliary Burner Semi-rapid Burners Ultra-rapid Triple-crown Burner Rapid Burner Control knobs... -
Page 5: Operation
If the control knobs become difficult to turn, please contact your local Zanussi Service Force Centre. Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. -
Page 6: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. SYMPTOM There is no spark when lighting the gas... -
Page 7: Instructions For The Installer
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: 680 mm Depth: 510 mm CUT OUT DIMENSIONS Width: 560 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. -
Page 8: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB Safety (Installation and Use) Regulations (Current Edition) WITHOUT A COOKER HOOD ABOVE and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. -
Page 9: Installation
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. -
Page 10: Building In
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. -
Page 11: Electrical Connections
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240 V 50 Hz AC electrical supply. -
Page 12: Wiring Diagram
Wiring Diagram 220/240 Fault Finding Preliminary Electrical Systems Check Brown Blue START Isolate appliance and carry out: A: Earth Continuity check. Blue Green Brown Yellow Has inlet fuse blown? Inlet wiring faulty. Rectify any fault. PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue... - Page 13 Ignition System / Gas Ignition Ignitor does not spark Check plug top fuse replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the...
-
Page 14: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 15: Guarantee/Customer Service
Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ·... -
Page 16: European Guarantee
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: •... - Page 20 35687-8702 11/06...