Toshiba TL969 Digital Series Owner's Manual page 17

k
In step 9, when you select Assisted Setup;
Press OK, and the Assisted Setup screen will appear.
B b
Press or to select the desired AP and press OK.
NOTE: Check the MAC address on the label of the AP
or in the manual, and select your AP.
B b
or to select Security Key and press OK.
Press
The Software Keyboard window will appear (page 50).
Input the Security Key by using the Software
Keyboard. To save your setting, press the BLUE
button.
NOTE:
• The Security Key must adhere to these conditions:
- TKIP/AES: 8-63 ASCII or 64 Hex characters
- WEP: 5 or 13 ASCII or 10 or 26 Hex characters
• There is only one key ID to set for WEP encryption.
B b
Press or to highlight Done and press OK.
NOTE:
• If Network Name is not displayed, see Manual Setup
below to set Network Name before pressing Done.
• If BACK is pressed before Done is selected, settings
are not saved.
When the message "Wireless configuration is
complete." appears on screen, press OK.
The screen will skip to step 13.
l
In step 9, when you select Manual Setup;
Press OK, and the Manual Setup screen will appear.
B b
Press or to select Network Name and press OK.
The Software Keyboard window will appear (page 50).
Input the Network Name by using the Software
Keyboard. To save your setting, press the BLUE
button.
B b
Press or to select Authentication and then press
C c
or to select Open System, Shared Key, WPA-
PSK or WPA2-PSK.
B b
Press or to select Encryption, and then press
c
or to select None, WEP, TKIP or AES.
NOTE:
• Certain encryption types are only compatible with
specific authentication types.
- When Authentication is Open System, only WEP
or None is compatible.
- When Authentication is Shared Key, only WEP is
compatible.
- When Authentication is WPA-PSK or WPA2-PSK,
only TKIP or AES is compatible.
• When incompatible Authentication/Encryption
pairings are detected, a warning message will be
displayed, and no connection attempt will be made
until the incompatibility is resolved.
• There is only one key ID to set for WEP encryption.
B b
Press or
Input the Security Key by using the Software
Keyboard (page 50).
To save your setting, press the BLUE button.
This item is grayed out when Encryption is None.
When Encryption is WEP, Key ID setting is available.
B b
Press or
select 1(default), 2, 3 or 4.
B b
Press or
When the message "Wireless configuration is
complete." appears on screen, press OK.
NOTE: Settings are not saved if BACK is pressed
before Done is selected.
m
The Advanced Network Setup screen will appear.
When the DHCP function of the router connected
with this TV is On, you can set Auto Setup to On or
Off. (This should usually be set to On.)
When the DHCP function of the router is Off, set Auto
Setup to Off, and set the IP Address DNS address(es)
manually.
Advanced Network Setup
IP Address Setup
Auto Setup
IP Address
Subnet Mask
Default Gateway
DNS Setup
Auto Setup
Primary DNS Address
Secondary DNS Address
MAC Address
You can view the fixed MAC address for the TV, if one
is installed.
C
B b
Press or
n
Press OK, and Network Connection Test will start.
A message will appear to indicate if the connection
was successful or if could not be completed.
Network connection was completed successfully.
NOTE: The result of Network Connection Test does
not always guarantee the connection.
To cancel the Network Connection Test:
Press BACK while searching for the Internet
connection.
17
SETTING UP YOUR TV
to select Security Key and press OK.
C
to select Key ID and press
to select Done and press OK.
On
XXX . XXX . XXX . XXX
XXX . XXX . XXX . XXX
XXX . XXX . XXX . XXX
On
XXX . XXX . XXX . XXX
XXX . XXX . XXX . XXX
00:11:22:33:44:55
Next
to select Next.
OK
c
or to