Related Manuals for Raisecom RC953-8FE16E1
Summary of Contents for Raisecom RC953-8FE16E1
-
Page 1: User Manual
RC953-8FE16E1 Inverse Multiplexing Ethernet Gateway User manual Raisecom Technology Co., Ltd (06/2006) -
Page 2: Table Of Contents
Contents Cautions......................1 Overview......................2 2.1. Main features ................... 2 2.2. Part number specification................. 3 2.3. Dimension ....................3 Parameters ......................4 3.1. Basic configuration................... 4 3.2. Ethernet interface parameters..............4 3.3. E1 interface parameters................4 3.4. CONSOLE interface parameters.............. 5 3.5. -
Page 3: Cautions
Raisecom Technology Co., Ltd 1. Cautions Please read the following notices carefully before installing and using the device, Raisecom does not respond to any loss that caused by violating safety notice. This series product is integrated device that has precise elements, please avoid violent shakes and impacts, and do not disassemble or maintain the device yourself. -
Page 4: Overview
Inverse Multiplexing for enlarging much more bandwidth. RC953-8FE16E1 provides 8 Ethernet ports and 16 E1 ports (both balanced and unbalanced) for subscribers and functions as a bridge between IP-based network and leased circuits. -
Page 5: Part Number Specification
Raisecom Technology Co., Ltd E1 loop back and BERT function Complete E1 line indicators on front panel E1 interface type: 2 DB37 for both balanced and unbalanced interfaces SNMP, CONSOLE and Telnet management (any of the 8 fast Ethernet can be SNMP network management interface) and support local and remote field firmware upgrade. -
Page 6: Parameters
Raisecom Technology Co., Ltd 3. Parameters 3.1. Basic configuration Main circuit: 8 fast Ethernet ports, 16 E1 ports. Power supply: two power supply modules, 90-264V/AC or -36V- -72V/DC. Management interface: CONSOLE, SNMP network management interface (utilize any of the 8 fast Ethernet ports). -
Page 7: Console Interface Parameters
Raisecom Technology Co., Ltd and is configurable There are three status indicators for each E1 circuit: LOS: Loss of Signal (local) LAL: local E1 general alarm, including AIS(alarm indication signal), LOF( Loss of Frame), CRC(Cyclic Redundancy Check) RAL: remote E1 alarm, including LOS, AIS, LOF, CRC... -
Page 8: How To Use
Raisecom Technology Co., Ltd 4. How to use 4.1. Front panel explanation RC953-8FE16E1 Figure 4-1 Front Table 4-1 Explanation of RC953-8FE16E1 front panel Explanati Indicator Description color Grounding Green SYS, Flashing indicates CPU work normally. PWR, ON indicates equipment is powered on. -
Page 9: Rear Panel Explanation
(Bottom) RAL: remote general alarm, including LOS, AIS, LOF, CRC. *note: when both LOS and LAL are ON at the same time, this indicates GID alarm. 9-16 DB37 connector which connects with special cable. connector 4.2. Rear panel explanation Figure 4-2 rear panel of RC953-8FE16E1... - Page 10 Raisecom Technology Co., Ltd Table 4-2: explanation of RC953-8FE16E1 rear panel Numb Explanation Description Power supply switch for the ON/OFF. device Power supply Two types, AC and DC. connector...
-
Page 11: Typical Application
Raisecom Technology Co., Ltd 5. Typical application Figure 5-1 point-to-point topology Figure 5-2 point-to-multi point topology... -
Page 12: Installation & Preparation
Configure the equipment according to the configuration guide ● Use the equipment correctly 6.2. Installation 6.2.1. Cable preparation The following cables need to be prepared: Table 6-1 Cable specification for RC953-8FE16E1 connectors Connector Cable specification 10/100Mbps Electrical Ethernet connector Cat. 5 100Base-T UTP,... -
Page 13: Connect The Fast Ethernet Port
6.2.2. Connect the fast Ethernet port Connect one end of the Cat. 5 UTP cable with Ethernet router/switch and one end of the cable with the fast Ethernet port of RC953-8FE16E1. The LNK/ACT indicator will be ON after correct connection. -
Page 14: Service Configuration
Make sure no reverse connection, or no short circuited, and then turn on power. When Power Supply is turned on, the PWR indicator should be ON. 6.2.6. Service configuration Please refer to the command notebook and configuration guide of RC953-8FE16E1 for the service configuration. - Page 15 ● Ethernet LINK indicator OFF Answer: please check if the UTP cable is broken off first and then check if the equipment that connects with RC953-8FE16E1 works normally. Please make sure that the correct Ethernet cable is used. ● Packets loss during traffic transmitting Answer: Firstly, please check the connection of Ethernet and E1 cables, and make sure the Channel, Map and DIP-switch configuration is correct.
-
Page 16: Appendix A: How To Make Console Cable
Raisecom Technology Co., Ltd 8. Appendix A: How to make CONSOLE cable Pin definitions: RJ45 pins Function DS9 pins DSR# DTR# “-” indicates the relative RJ45 pin is not connected (NC). DB9 pins which are not in the list are not connected (NC). -
Page 17: Appendix B: Abbreviations
Raisecom Technology Co., Ltd 9. Appendix B: Abbreviations Ethernet over PDH EoPDH Pseudo-synchronous Digital Hierarchy. - Page 18 Raisecom Technology Co., Ltd @2006 Raisecom Technology Co., Ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification.