Poulan Pro 2750 Operator's Manual
Saw
Hide thumbs
Also See for 2750:
- Instruction manual (56 pages) ,
- Operator's manual (14 pages) ,
- Assembly (108 pages)
Table of Contents
Advertisement
Quick Links
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l'outil au détaillant.
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA :
Lea el manual del operador y siga todas las advertencias e enstruc-
ciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel de l'utilisateur et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Augusta, GA 30907
WCI Outdoor Products, Inc.
1- -800- -554- -6723
www.poulan.com
Operator's Manual
Manual del Operador
Manuel de L'utilisateur
2750 / 2775 / 2900 / 3050
R
U L
R
530088787
10/16/00
Advertisement
Table of Contents
Related Manuals for Poulan Pro 2750
Summary of Contents for Poulan Pro 2750
- Page 1 Operator’s Manual Manual del Operador Manuel de L’utilisateur 2750 / 2775 / 2900 / 3050 WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA : Lea el manual del operador y siga todas las advertencias e enstruc- ciones de seguridad.
-
Page 2: Safety Rules
S Keep fuel and oil caps, screws, and fas- shoulder length. teners securely tightened. S Keep all parts of your body away from the S Use only Poulan accessories and replace- chain when the engine is running. ment parts as recommended. S Keep children, bystanders, and animals a... -
Page 3: Maintain Control
S Move at least 10 feet (3 meters) from fuel- Avoid Obstructions ing site before starting engine. S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. -
Page 4: Kickback Safety Features
Symmetrical Guide Bar Large Radius Tip Elbow locked S Low--Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Low-- Thumb on underside of Kickback Chain has met kickback per- handlebar formance requirements when tested on a representative sample of chain saws be-... -
Page 5: Safety Notice
and bar as original equipment. Repairs on a 4443. All U.S. forest land and the states of chain brake should be made by an autho- California, Idaho, Maine, Minnesota, New rized servicing dealer. Take your unit to the Jersey, Oregon, and Washington require by place of purchase if purchased from a ser- law that many internal combustion engines vicing dealer, or to the nearest authorized... -
Page 6: Chain Tension
CHAIN TENSION (Including units with Inside view of chain already installed) Chain Brake NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage. -
Page 7: Operation
OPERATION KNOW YOUR SAW READ THIS OPERATOR’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Front Handle Chain Adjustment Front Hand Guard... -
Page 8: Starting A Cold Engine
Hold saw firmly while pulling starter rope 2-cycle air-cooled engine oil. recommend Poulan/Weed EaterR brand oil. Starter rope handle If you do not use this oil, use a good quality Left hand 2-cycle air-cooled oil designed to be mixed at... -
Page 9: Cutting Methods
STARTING A WARM ENGINE: back toward the front handle as far as possible. S Move ON/STOP switch to the ON position. S When cutting with the saw, the chain brake S Pull the choke/fast idle lever out to the full must be disengaged. -
Page 10: Tree Felling Techniques
force the cut, damage to the bar, Plan a clear retreat path chain, or engine can result. Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unnec- Direction of Fall essary wear can occur to the chain,... - Page 11 Hinge holds tree on stump and helps use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log. control fall Use a wedge to remove pinched saw Opening of felling Turn saw and use a plastic or wooden wedge to force cut open.
-
Page 12: Limbing And Pruning
Using a log for support S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released. S Keep a clear work area. Frequently clear branches out of the way to avoid tripping over them. -
Page 13: Air Filter
Muffler Diffuser MAINTENANCE SCHEDULE Spark Lubricate bar Arresting sprocket hole ..After each use Screen Check: Muffler Fuel mixture level ..Before each use Cover Bar lubrication ..Before each use Screws Chain tension... -
Page 14: Chain Sharpening
S When rail top is uneven, use a flat file to re- STORAGE store square edges and sides. WARNING: File Rail Edges Stop engine and allow to and Sides cool, and secure the unit before storing or Square transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, Worn Groove... -
Page 15: Limited Warranty
LY STIPULATED HEREIN. rants to the original purchaser that each new SOME STATES DO NOT ALLOW LIMITA- Poulan or Poulan Pro brand gasoline chain TIONS ON HOW LONG AN IMPLIED WAR- saw is free from defects in material and RANTY LASTS OR THE EXCLUSION OR... - Page 16 Poulan/Weed you should contact your nearest authorized Eater will repair your lawn and garden equip- service center or call Poulan/Weed Eater ment engine at no cost to you. Expenses 1--800--554--6723 WARRANTY PERIOD: covered under warranty include diagnosis, Any warranted part which is not scheduled parts and labor.