Related Manuals for Zanussi ZGM 782
Summary of Contents for Zanussi ZGM 782
- Page 1 GAS HOB ZGM 782 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance...
-
Page 2: Important Safety Information
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation Never leave the hob unattended when cooking with This hob must be installed by qualified personnel, oil and fats. -
Page 3: Table Of Contents
Contents For the Installer For the User Instructions for the Installer Important Safety Information Important safety requirements Description of the Hob Installation Operation Building In Maintenance and Cleaning Electrical connections Something Not Working? Wiring Diagram Guarantee/Customer Service Fault Finding European guarantee Commissioning Conversion from Natural Gas to LPG Guide to Use the instructions... -
Page 4: Description Of The Hob
Description of the Hob Auxiliary Burner Semi-rapid Burners Rapid Burner Ultra-rapid Triple-crown Burner Control knobs... -
Page 5: Operation
If the control knobs become difficult to turn, please To ensure maximum burner efficiency, you should only contact your local Zanussi Service Force Centre. use pots and pans with a flat bottom fitting the size of the burner used (see table). -
Page 6: Something Not Working
After cleaning, be sure to wipe dry with a soft cloth. Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. SYMPTOM SOLUTION... -
Page 7: Instructions For The Installer
Instructions for the Installer Ignition HT Spark Engineers technical data Spark Generator Ispra Control's BF 80066 OVERALL DIMENSIONS 220- 240V 0.6 VA T 120 Spark Gap Fixed Width: 680 mm. Depth: 510 mm. Rear Left Burner (rapid) Heat Input 2.8 kW Natural Gas (10239 BTU/HR) CUT OUT DIMENSIONS 2.8 kW L.P.G. -
Page 8: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. -
Page 9: Installation
Installation IMPORTANT: This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. -
Page 10: Building In
Building In Building over a cupboard or Building over a kitchen unit with drawer door Proper arrangements must be taken in designing the If the hob is to be installed above a cupboard or drawer it furniture unit, in order to avoid any contact with the bottom will be necessary to fit a heat resistant board below the of the hob which can be heated when it is operated. -
Page 11: Electrical Connections
Seal FO 0199 Electrical connections Any electrical work required to install this hob Permanent Connection should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. -
Page 12: Wiring Diagram
Wiring Diagram 1. IGNITOR SWITCHES 2. IGNITOR UNIT Fault Finding Preliminary Electrical Systems PLUG (with cover SOCKET Check removed) (face view) Earth Wire Brown Blue Green/Yellow Green Yellow START Isolate appliance Neutral Wire and carry out: Blue A: Earth Continuity check. - Page 13 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance...
-
Page 14: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 15: Guarantee/Customer Service
Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ·... -
Page 16: European Guarantee
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: •... - Page 20 35679-0202 11/06...