SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS DANGER ! THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. GENERAL OPERATION • Keep machine free of grass, leaves or other debris •...
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS SERVICE DO NOT • Do not turn on slopes unless necessary, and then, • The operation of any mower can result in foreign turn slowly and gradually downhill, if possible. objects thrown into the eyes, which can result in severe eye damage. Always wear safety •...
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow WARNING! machine to cool before storing. Battery posts, terminals and related • Stop and inspect the equipment if you strike an accessories contain lead and lead object.
UNPACKING INSTRUCTIONS CONTAINER CONTENTS • Remove all parts and packing materials from 2 - Soft bag containers 1 - Bag of Hardware carton. 1 - Upper Chute 1 - Lower Chute • Check carton contents against list. Be sure all 1 - Cover Assembly 1 - Mounting Hardware parts are there.
ASSEMBLY INSTALL PLATE AND HANGER MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY For ease of assembly, you may wish assistance from Using hardware provided in kit, attach support another person for mounting the cover assembly to mount to unit. mower. Attach hanger bracket to support mount. Do not Position cover assembly on the ground behind the fully tighten nuts at this time.
ASSEMBLY CONTAINER INSTALLATION LOWER CHUTE INSTALLATION Install containers on support frame, overlapping Raise and hold deflector shield in upright position. containers at center tube. Fit lower chute as shown and hook rear latch to Note: One container should always overlap the mower deck. other container at the center tube. Align the bracket slot on lower chute with the Close cover and lock latch handle over support deflector bracket tab on the mower deck. Slide...
ASSEMBLY UPPER CHUTE INSTALLATION With ¼" drill bit, add a new hole 4¾" inches from Slide upper chute onto lower chute, lining up the top of the chute, down along the side seam. notches and channels. Attach bungee latch assembly from kit. Stretch bungee latch up onto acorn nut on upper chute to secure.
ASSEMBLY CHUTE / HOOD INSTALLATION LEVELING MOWER DECK Push upper chute through the gasketed opening in Be sure deck is properly leveled for best mower the cover assembly. performance. See your mower operator’s manual for instructions. Rotate chute so the chute opening is downwards toward the container bags.
OPERATION IMPROVED BAGGING TIPS Follow the mower operation instructions in the mower • If the grass catcher fails to pick up cut grass operator’s manual. or leaves, it is an indication that clogging has When using the grass catcher on a lawn where grass occurred in the system or that the grass catcher and leaf bagging equipment has not been used, thatch containers are full.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any When grass catcher is to be stored for a period of maintenance. time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. •...
TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut ft./lbs ft./lbs ft./lbs ft./lbs ¼ ½ ¾ 1060 1410 1912 ** Grade 5 - Minimum commercial quality (lower quality not recommended) Metric Standard Hardware Grade Grade 8.8 Grade 10.9 Grade 12.9 ft./lbs ft./lbs...
SECTION 1: LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship from the date of purchase for the period of the applicable “Warranty Schedule” of the Product as set forth below. Additional limitations are described in Section 2 through 6, inclusive.
Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address of the selling retailer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner, no later than thirty (30) days from date of the operational problem or failure.