Table of Contents
Advertisement
Preparation
When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP] to change to regular mode.
1
Set your car's ignition switch to the ACC
or ON position.
2
Press [SRC] (PWR: POWER).
The demonstration screen appears.
Example: CQ-C9901N
3
Press [DISP: DISPLAY].
The demonstration screen is cancelled, and no more
appears.
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Insulation film
Battery Replacement
q Remove the battery holder
Tough pointed object
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
w Put a battery in the case with
(+) side facing up.
e Put the case back.
Caution
Be sure to select OFF when your car has no
ACC position in the ignition switch. Failure
to do this could cause the battery to go
dead.
OFF
ACC
IGN
10
CQ-C9901N/C9701N
CS
SRC
SRC
Note: If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: POWER) for 4 sec. or more. (at ACC on
setting)
Warning
¡Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡ Remove and dispose of an old battery immediately.
¡ Do not disassemble, heat or short a battery. Do
not throw a battery into a fire or water.
¡ Follow local regulations when disposing of a bat-
tery.
¡Improper use of a battery may cause overheating,
Back side
an explosion or ignition, resulting in injury or a fire.
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
w
(Included in the remote control)
q
Battery Life: Approximately 6 months under normal
use (at room temperature)
2
3
For a ACC-equipped car, select ON.
(a
following functions are available. (default: off)
¡
The power is turned on automatically when inserting a
disc or magazine.
¡
The clock can be displayed even if the power is off.
(a
page 15)
The following functions are activated when the Security
Function is ON.
¡
The security indicator blinks when removing the face
plate.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡
Subwoofer level adjustment
¡
Subwoofer low pass filter
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1
Press [SRC: SOURCE] to select the
AUX1 mode.
2
Press [MENU] to display the menu dis-
play.
Notes:
¡
Adjust the clock when "NO CT" appears on the dis-
play.
¡
When a broadcast of FM Radio Data System is
received, the clock is put right automatically by the
Clock Time service.
1
Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
page 38) The
for 2 sec. or more.
2
Press []] or [[] to display the DIS-
PLAY menu.
3
Press [
4
Press [BAND] (SET) to confirm the dis-
play.
¡
The alarm sounds and the message appears on the
(a
page 38)
screen to warn you to remove the face plate at power
off.
Security Indicator
For using the remote control, hold down [MENU]
for 2 sec. or more.
(a
page 36)
3
Press [BAND] (SET) to adjust.
(a
page 36)
Note: When using an external TV unit manufactured by
a third party, select the TV mode.
(a
page 14)
4
Press [MENU] to confirm the adjust-
ment.
5
Adjust the setting value.
(a
page 22)
[[]
: Adjusting minutes
[]]
: Adjusting hours
[
]
}
: Forward
[
{
]
: Backward
6
Press [BAND] (SET) to confirm the
adjustment.
Note: For cancellation of clock adjustment, press
[DISP].
] to select "CLOCK ADJ".
{
7
Press [MENU].
For using the remote control, hold down [MENU]
for 2 sec. or more.
CQ-C9901N/C9701N
: TV
: Other devices (Default)
11
Advertisement
Table of Contents
