Panasonic CQ-C8100N Operating Instructions Manual page 9

Radio
This chapter explains how to listen to the radio.
1
Press [SOURCE] to select the radio
mode.
2
Press [BAND] to select a band.
Notes:
¡ For tuning in on only stations whose receiving
conditions are good in the station search, set
LOCAL to ON. ( page 17)
a
For reducing noise when a receiving FM stereo
¡
wave is weak, set FM MONO to ON. (
Band
Preset Number
16
CQ-C8300N
3
Select a station.
Frequency adjustment
[]] (TUNE): Lower
[[] (TUNE): Higher
Note: Hold down more than 0.5 sec. or more and
release for station search.
Preset station selection
[{] (P·SET: Preset): Lower preset number
[}] (P·SET: Preset): Higher preset number
Note: Direct selection can be executed with [1] to
[6] buttons on remote control.
page 17)
a
Frequency
Lights when LOCAL is
activated.
Lights while receiving an
FM stereo signal.
Lights when MONO is
activated. ( a page 17)
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing [}]
BAND BAND
(P·SET) or [{] (P·SET).
Note: Direct selection can be executed with [1] to [6]
buttons on remote control.
Auto Preset Memory (APM)
Six stations with the first highest to the 6th highest in
signal strength will be preset to each band. When FM1 is
selected, 18 stations in total will be preset to FM1 to FM3.
1
Select a band.
2
Hold down
[BAND] (APM)
for 2 sec. or
more.
The preset stations under best receiving conditions
are received for 5 sec. each after presetting the sta-
tions (SCAN). To stop scanning, press [}] or [{].
Notes:
¡ New stations overwrite existing saved stations. (For
FM1, FM2 and FM3 at the same time, select FM1.)
¡ Only RDS stations will be saved at default setting (AF ON).
To select non RDS stations too, set AF
Note: In AM mode, only LOCAL can be selected.
1
Press [MENU] to display the menu dis-
play.
For using the remote
control, hold down
[MENU] for 2 sec. or
more.
2
Press [
adjusted.
3
Press [BAND]
( page 17)
a
(SET) to adjust.
4
Press [MENU] to confirm the adjust-
ment.
For using the remote control, hold down [MENU]
for 2 sec. or more.
¡ If you would like to preset FM stations of different
areas in different bands, first, execute the APM opera-
tion when FM1 is selected, then execute the APM
operation in a different area when FM2 is selected and
another APM operation in another different area when
FM3 is selected.
Manual station preset
1
Tune in to a station.
2
Hold down
more.
CQ-C8300N
number by pressing
BAND BAND
4
Preset the station by holding down
or
[{]
Frequency/preset number blinks once.
Notes:
¡ New stations overwrite existing saved stations.
¡ In step 2, a station can be registered by holding down
the numeric button [1]~[6] 2 sec. or more.
¡ To stop presetting stations, press [DISP] (Display).
OFF.(a page 19)
CQ-C8300N
MONO (Monaural)
BAND
Noise reduction when the signal strength decreases
Receiving in stereo
} ] or [ { ] to select a mode to be
(Default)
CQ-C8300N
LOCAL
BAND BAND
Setting when searching for a station
Searching even for a
relatively low-intensity
radio wave station
(Default)
or for 2 sec. or
[}] [{]
3
Select a
preset
or .
[}] [{]
[}]
for 2 sec. or more.
Receiving in mono and
reducing the noise level
( lights.)
Searching only for a high-
intensity radio wave
station (
lights.)
17